=> run nfsargs addip addtty => run loadlinux Speed: 1000, full duplex Using TSEC0 device TFTP from server 192.168.1.24; our IP address is 192.168.1.83 Filename '2623'. Load address: 0x200000 Loading: Got error 4 T ################################################################# ################################################################# ################################################################# ################################################################# ########################### done Bytes transferred = 1465976 (165e78 hex) Speed: 1000, full duplex Using TSEC0 device TFTP from server 192.168.1.24; our IP address is 192.168.1.83 Filename '2623.dtb'. Load address: 0x400000 Loading: # done Bytes transferred = 3566 (dee hex) ## Booting image at 00200000 ... Image Name: Linux-2.6.23 Created: 2007-10-18 20:07:31 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1465912 Bytes = 1.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Booting using flat device tree at 0x400000 Using MPC8313 RDB machine description Linux version 2.6.23 (leon@witty) (gcc version 4.1.2) #1 Thu Oct 18 21:37:04 CEST 2007 console [udbg0] enabled setup_arch: bootmem mpc8313_rdb_setup_arch() Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0 arch: exit Zone PFN ranges: DMA 0 -> 32768 Normal 32768 -> 32768 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 32768 Built 1 zonelists in Zone order. Total pages: 32512 Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.24:/nfsroot/rootfs ip=192.168.1.83:192.168.1.24:192.168.1.254:255.255.255.0:mpc8313erdb:eth0:off panic=1 console=ttyS0,115200 IPIC (128 IRQ sources) at fdefa700 PID hash table entries: 512 (order: 9, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 126632k/131072k available (2880k kernel code, 4276k reserved, 132k data, 91k bss, 152k init) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Probing PCI hardware Generic PHY: Registered new driver SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 18) is a 16550A console handover: boot [udbg0] -> real [ttyS0] serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 21) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: module loaded Gianfar MII Bus: probed eth0: Gianfar Ethernet Controller Version 1.2, 00:04:9f:ef:23:33 eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:00:7e:21 eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation Cicada Cis8204: Registered new driver Cicada Cis8201: Registered new driver physmap platform flash device: 01000000 at fe000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 physmap-flash.0: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. usbmon: debugfs is not available fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 38, io base 0xe0023000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i2c /dev entries driver WDT driver for MPC83xx initialized. mode:reset timeout=65535 (25 seconds) md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) e0024520:01 not found eth0: Could not attach to PHY IP-Config: Failed to open eth0 IP-Config: Device `eth0' not found. md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Looking up port of RPC 100003/2 on 192.168.1.24 rpcbind: server 192.168.1.24 not responding, timed out Root-NFS: Unable to get nfsd port number from server, using default Looking up port of RPC 100005/1 on 192.168.1.24 rpcbind: server 192.168.1.24 not responding, timed out Root-NFS: Unable to get mountd port number from server, using default mount: server 0.0.0.16 not responding, timed out Root-NFS: Server returned error -5 while mounting /nfsroot/rootfs VFS: Unable to mount root fs via NFS, trying floppy. VFS: Cannot open root device "nfs" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) Rebooting in 1 seconds..