[    0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
[    0.000000]  BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003f690000 (usable)
[    0.000000]  BIOS-e820: 000000003f690000 - 000000003f700000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[    0.000000] 118MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] found SMP MP-table at 000f6680
[    0.000000] Entering add_active_range(0, 0, 259728) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   259728
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   259728
[    0.000000] On node 0 totalpages: 259728
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 237 pages used for memmap
[    0.000000]   HighMem zone: 30115 pages, LIFO batch:7
[    0.000000] DMI present.
[    0.000000] ACPI: RSDP signature @ 0xC00F6650 checksum 0
[    0.000000] ACPI: RSDP 000F6650, 0024 (r2 PTLTD )
[    0.000000] ACPI: XSDT 3F69257E, 006C (r1 ACRSYS ACRPRDCT  6040000  LTP        0)
[    0.000000] ACPI: FACP 3F69BC38, 00F4 (r3 INTEL  CALISTGA  6040000 ALAN        1)
[    0.000000] ACPI: DSDT 3F692F86, 8C3E (r2 INTEL  CALISTGA  6040000 MSFT  3000000)
[    0.000000] ACPI: FACS 3F69CFC0, 0040
[    0.000000] ACPI: APIC 3F69BD2C, 0068 (r1 INTEL  CALISTGA  6040000 LOHR       5A)
[    0.000000] ACPI: HPET 3F69BD94, 0038 (r1 INTEL  CALISTGA  6040000 LOHR       5A)
[    0.000000] ACPI: MCFG 3F69BDCC, 003C (r1 INTEL  CALISTGA  6040000 LOHR       5A)
[    0.000000] ACPI: APIC 3F69BE08, 005A (r1 PTLTD  	 APIC    6040000  LTP        0)
[    0.000000] ACPI: BOOT 3F69BE62, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
[    0.000000] ACPI: SLIC 3F69BE8A, 0176 (r1 ACRSYS ACRPRDCT  6040000 acer        0)
[    0.000000] ACPI: SSDT 3F692AD0, 04B6 (r1  PmRef  Cpu0Cst     3001 INTL 20050624)
[    0.000000] ACPI: SSDT 3F6925EA, 04E6 (r1  PmRef    CpuPm     3000 INTL 20050624)
[    0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[    0.000000] ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] Processor #0 6:15 APIC version 20
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[    0.000000] Built 1 zonelists.  Total pages: 257699
[    0.000000] Kernel command line: root=UUID=cee918bb-c207-41a8-beb0-d9af7bce0b11 ro quiet splash
[    0.000000] mapped APIC to ffffd000 (fee00000)
[    0.000000] mapped IOAPIC to ffffc000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Detected 1600.160 MHz processor.
[   13.625465] Console: colour VGA+ 80x25
[   13.625769] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   13.626073] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   13.654139] Memory: 1018044k/1038912k available (2015k kernel code, 20156k reserved, 916k data, 364k init, 121408k highmem)
[   13.654149] virtual kernel memory layout:
[   13.654150]     fixmap  : 0xfff4d000 - 0xfffff000   ( 712 kB)
[   13.654151]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   13.654152]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   13.654154]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   13.654155]       .init : 0xc03e3000 - 0xc043e000   ( 364 kB)
[   13.654156]       .data : 0xc02f7d26 - 0xc03dce84   ( 916 kB)
[   13.654157]       .text : 0xc0100000 - 0xc02f7d26   (2015 kB)
[   13.654160] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   13.654196] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[   13.654352] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[   13.654357] hpet0: 3 64-bit timers, 14318180 Hz
[   13.735255] Calibrating delay using timer specific routine.. 3203.78 BogoMIPS (lpj=6407577)
[   13.735281] Security Framework v1.0.0 initialized
[   13.735289] SELinux:  Disabled at boot.
[   13.735301] Mount-cache hash table entries: 512
[   13.735445] CPU: After generic identify, caps: afebfbff 20100000 00000000 00000000 0000e31d 00000000 00000001
[   13.735453] monitor/mwait feature present.
[   13.735455] using mwait in idle threads.
[   13.735460] CPU: L1 I cache: 32K, L1 D cache: 32K
[   13.735463] CPU: L2 cache: 1024K
[   13.735466] CPU: After all inits, caps: afebfbff 20100000 00000000 00003940 0000e31d 00000000 00000001
[   13.735476] Compat vDSO mapped to ffffe000.
[   13.735491] Checking 'hlt' instruction... OK.
[   13.751354] SMP alternatives: switching to UP code
[   13.751579] Freeing SMP alternatives: 11k freed
[   13.751854] Early unpacking initramfs... done
[   14.109492] ACPI: Core revision 20070126
[   14.109552] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   14.113906] CPU0: Intel(R) Celeron(R) M CPU        520  @ 1.60GHz stepping 06
[   14.113931] Total of 1 processors activated (3203.78 BogoMIPS).
[   14.114127] ENABLING IO-APIC IRQs
[   14.114323] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   14.258487] Brought up 1 CPUs
[   14.258588] Booting paravirtualized kernel on bare hardware
[   14.258662] Time: 20:15:00  Date: 09/20/107
[   14.258681] NET: Registered protocol family 16
[   14.258758] EISA bus registered
[   14.258763] ACPI: bus type pci registered
[   14.283872] PCI: PCI BIOS revision 2.10 entry at 0xfd6c2, last bus=12
[   14.283874] PCI: Using configuration type 1
[   14.283876] Setting up standard PCI resources
[   14.285660] ACPI: EC: Look up EC in DSDT
[   14.286312] ACPI: EC: GPE=0x17, ports=0x66, 0x62
[   14.305545] ACPI: System BIOS is requesting _OSI(Linux)
[   14.305548] ACPI: Please test with "acpi_osi=!Linux"
[   14.305549] Please send dmidecode to linux-acpi@vger.kernel.org
[   14.306029] ACPI: Interpreter enabled
[   14.306032] ACPI: (supports S0 S3 S4 S5)
[   14.306047] ACPI: Using IOAPIC for interrupt routing
[   14.311424] ACPI: EC: GPE=0x17, ports=0x66, 0x62
[   14.311471] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   14.311483] PCI: Probing PCI hardware (bus 00)
[   14.312276] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[   14.312280] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[   14.313147] PCI: Transparent bridge - 0000:00:1e.0
[   14.313287] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   14.313586] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[   14.313716] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[   14.313842] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[   14.313981] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[   14.318308] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[   14.318420] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[   14.318524] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[   14.318626] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[   14.318728] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[   14.318830] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[   14.318932] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[   14.319033] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[   14.319147] Linux Plug and Play Support v0.97 (c) Adam Belay
[   14.319158] pnp: PnP ACPI init
[   14.319168] ACPI: bus type pnp registered
[   14.321861] pnp: PnP ACPI: found 9 devices
[   14.321863] ACPI: ACPI bus type pnp unregistered
[   14.321867] PnPBIOS: Disabled by ACPI PNP
[   14.321915] PCI: Using ACPI for IRQ routing
[   14.321918] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   14.321923] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
[   14.321975] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
[   14.322025] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.0
[   14.322073] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
[   14.322122] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
[   14.322170] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
[   14.322219] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.2
[   14.322267] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.2
[   14.322315] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.2
[   14.353438] NET: Registered protocol family 8
[   14.353440] NET: Registered protocol family 20
[   14.353504] pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[   14.353508] pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
[   14.353511] pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
[   14.353514] pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
[   14.353520] pnp: 00:03: iomem range 0xfed00000-0xfed003ff could not be reserved
[   14.354306] Time: tsc clocksource has been installed.
[   14.354322] Switched to high resolution mode on CPU 0
[   14.383793] PCI: Bridge: 0000:00:1c.0
[   14.383797]   IO window: 2000-2fff
[   14.383803]   MEM window: 54000000-540fffff
[   14.383809]   PREFETCH window: disabled.
[   14.383824] PCI: Bridge: 0000:00:1c.1
[   14.383826]   IO window: disabled.
[   14.383832]   MEM window: 54100000-541fffff
[   14.383836]   PREFETCH window: disabled.
[   14.383842] PCI: Bridge: 0000:00:1c.2
[   14.383844]   IO window: disabled.
[   14.383849]   MEM window: disabled.
[   14.383854]   PREFETCH window: disabled.
[   14.383862] PCI: Bus 11, cardbus bridge: 0000:0a:09.0
[   14.383864]   IO window: 00003000-000030ff
[   14.383870]   IO window: 00003400-000034ff
[   14.383875]   PREFETCH window: 50000000-53ffffff
[   14.383880]   MEM window: 58000000-5bffffff
[   14.383885] PCI: Bridge: 0000:00:1e.0
[   14.383889]   IO window: 3000-3fff
[   14.383895]   MEM window: d0200000-d02fffff
[   14.383900]   PREFETCH window: 50000000-53ffffff
[   14.383931] PCI: Enabling device 0000:00:1c.0 (0000 -> 0003)
[   14.383938] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[   14.383947] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   14.383971] PCI: Enabling device 0000:00:1c.1 (0000 -> 0002)
[   14.383976] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
[   14.383983] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[   14.384010] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[   14.384017] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[   14.384029] PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
[   14.384035] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   14.384053] PCI: Enabling device 0000:0a:09.0 (0000 -> 0003)
[   14.384058] ACPI: PCI Interrupt 0000:0a:09.0[A] -> GSI 20 (level, low) -> IRQ 19
[   14.384075] NET: Registered protocol family 2
[   14.422204] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[   14.422283] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[   14.423245] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[   14.423641] TCP: Hash tables configured (established 131072 bind 65536)
[   14.423644] TCP reno registered
[   14.434305] checking if image is initramfs... it is
[   15.131690] Freeing initrd memory: 7353k freed
[   15.131836] Simple Boot Flag at 0x36 set to 0x1
[   15.132161] audit: initializing netlink socket (disabled)
[   15.132176] audit(1192911300.092:1): initialized
[   15.132247] highmem bounce pool size: 64 pages
[   15.133986] VFS: Disk quotas dquot_6.5.1
[   15.134029] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   15.134120] io scheduler noop registered
[   15.134122] io scheduler anticipatory registered
[   15.134124] io scheduler deadline registered
[   15.134139] io scheduler cfq registered (default)
[   15.134153] Boot video device is 0000:00:02.0
[   15.134320] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   15.134383] assign_interrupt_mode Found MSI capability
[   15.134386] Allocate Port Service[0000:00:1c.0:pcie00]
[   15.134419] Allocate Port Service[0000:00:1c.0:pcie02]
[   15.134521] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[   15.134582] assign_interrupt_mode Found MSI capability
[   15.134584] Allocate Port Service[0000:00:1c.1:pcie00]
[   15.134612] Allocate Port Service[0000:00:1c.1:pcie02]
[   15.134710] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[   15.134771] assign_interrupt_mode Found MSI capability
[   15.134773] Allocate Port Service[0000:00:1c.2:pcie00]
[   15.134802] Allocate Port Service[0000:00:1c.2:pcie02]
[   15.134956] isapnp: Scanning for PnP cards...
[   15.488781] isapnp: No Plug & Play device found
[   15.509458] Real Time Clock Driver v1.12ac
[   15.509677] hpet_resources: 0xfed00000 is busy
[   15.509708] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   15.510786] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   15.510958] input: Macintosh mouse button emulation as /class/input/input0
[   15.511028] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[   15.525487] i8042.c: Detected active multiplexing controller, rev 1.1.
[   15.532030] serio: i8042 KBD port at 0x60,0x64 irq 1
[   15.532035] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   15.532038] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   15.532040] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   15.532043] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   15.532232] mice: PS/2 mouse device common for all mice
[   15.532842] EISA: Probing bus 0 at eisa.0
[   15.532850] Cannot allocate resource for EISA slot 1
[   15.532853] Cannot allocate resource for EISA slot 2
[   15.532855] Cannot allocate resource for EISA slot 3
[   15.532876] EISA: Detected 0 cards.
[   15.532964] TCP cubic registered
[   15.532977] NET: Registered protocol family 1
[   15.533000] Using IPI No-Shortcut mode
[   15.533146]   Magic number: 11:369:296
[   15.533172]   hash matches device ttywd
[   15.533246]   hash matches device tty29
[   15.533433] Freeing unused kernel memory: 364k freed
[   15.624477] input: AT Translated Set 2 keyboard as /class/input/input1
[   16.752843] AppArmor: AppArmor initialized<5>audit(1192911301.592:2):  type=1505 info="AppArmor initialized" pid=1216
[   16.758957] fuse init (API version 7.8)
[   16.763366] Failure registering capabilities with primary security module.
[   16.778732] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   16.778738] ACPI: Processor [CPU0] (supports 8 throttling states)
[   16.778751] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[   16.782479] ACPI: Thermal Zone [THRM] (49 C)
[   17.333637] usbcore: registered new interface driver usbfs
[   17.333659] usbcore: registered new interface driver hub
[   17.333678] usbcore: registered new device driver usb
[   17.334427] USB Universal Host Controller Interface driver v3.0
[   17.334488] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
[   17.334499] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   17.334503] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   17.334633] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   17.334667] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820
[   17.334770] usb usb1: configuration #1 chosen from 1 choice
[   17.334797] hub 1-0:1.0: USB hub found
[   17.334803] hub 1-0:1.0: 2 ports detected
[   17.398559] SCSI subsystem initialized
[   17.415756] libata version 2.21 loaded.
[   17.437761] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 21
[   17.437773] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   17.437778] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   17.437800] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   17.437834] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001840
[   17.437922] usb usb2: configuration #1 chosen from 1 choice
[   17.437949] hub 2-0:1.0: USB hub found
[   17.437955] hub 2-0:1.0: 2 ports detected
[   17.541621] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[   17.541633] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   17.541637] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   17.541660] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   17.541694] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[   17.541788] usb usb3: configuration #1 chosen from 1 choice
[   17.541811] hub 3-0:1.0: USB hub found
[   17.541818] hub 3-0:1.0: 2 ports detected
[    3.820000] Marking TSC unstable due to: possible TSC halt in C2.
[    3.848000] Time: hpet clocksource has been installed.
[    3.888000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[    3.888000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[    3.888000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    3.888000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    3.888000] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
[    3.888000] usb usb4: configuration #1 chosen from 1 choice
[    3.888000] hub 4-0:1.0: USB hub found
[    3.888000] hub 4-0:1.0: 2 ports detected
[    3.992000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
[    3.992000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    3.992000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    3.992000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    3.992000] ehci_hcd 0000:00:1d.7: debug port 1
[    3.992000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    3.992000] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xd0644000
[    4.000000] Clocksource tsc unstable (delta = -127847223 ns)
[    4.024000] usb 2-2: new low speed USB device using uhci_hcd and address 2
[    4.024000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    4.024000] usb usb5: configuration #1 chosen from 1 choice
[    4.024000] hub 5-0:1.0: USB hub found
[    4.024000] hub 5-0:1.0: 8 ports detected
[    4.128000] ata_piix 0000:00:1f.2: version 2.11
[    4.128000] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[    4.284000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 21
[    4.284000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    4.284000] scsi0 : ata_piix
[    4.284000] scsi1 : ata_piix
[    4.284000] ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000118b0 irq 14
[    4.284000] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000118b8 irq 15
[    4.448000] ata1.00: ATA-7: Hitachi HTS541612J9SA00, SBDOC7DP, max UDMA/100
[    4.448000] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.464000] ata1.00: configured for UDMA/100
[    4.552000] usb 2-2: new low speed USB device using uhci_hcd and address 3
[    4.720000] usb 2-2: configuration #1 chosen from 1 choice
[    4.732000] usbcore: registered new interface driver hiddev
[    4.748000] input: USB Optical Mouse as /class/input/input2
[    4.748000] input: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.1-2
[    4.748000] usbcore: registered new interface driver usbhid
[    4.748000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[    4.784000] ata2.00: ATAPI: Optiarc CD-RW CRX880A, KX07, max UDMA/33
[    4.956000] ata2.00: configured for UDMA/33
[    4.956000] scsi 0:0:0:0: Direct-Access     ATA      Hitachi HTS54161 SBDO PQ: 0 ANSI: 5
[    4.956000] scsi 1:0:0:0: CD-ROM            Optiarc  CD-RW CRX880A    KX07 PQ: 0 ANSI: 5
[    4.972000] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[    4.972000] sd 0:0:0:0: [sda] Write Protect is off
[    4.972000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.972000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.972000] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[    4.972000] sd 0:0:0:0: [sda] Write Protect is off
[    4.972000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.972000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.972000]  sda: sda1 sda2 < sda5 >
[    5.016000] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.020000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    5.020000] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[    5.044000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    5.044000] Uniform CD-ROM driver Revision: 3.20
[    5.044000] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    5.204000] Attempting manual resume
[    5.204000] swsusp: Resume From Partition 8:5
[    5.204000] PM: Checking swsusp image.
[    5.208000] PM: Resume from disk failed.
[    5.220000] EXT3-fs: INFO: recovery required on readonly filesystem.
[    5.220000] EXT3-fs: write access will be enabled during recovery.
[    6.228000] kjournald starting.  Commit interval 5 seconds
[    6.228000] EXT3-fs: recovery complete.
[    6.228000] EXT3-fs: mounted filesystem with ordered data mode.
[   13.052000] Linux agpgart interface v0.102 (c) Dave Jones
[   13.116000] agpgart: Detected an Intel 945GM Chipset.
[   13.116000] agpgart: Detected 7932K stolen memory.
[   13.132000] agpgart: AGP aperture is 256M @ 0xc0000000
[   13.172000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   13.176000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   13.576000] PCI: Enabling device 0000:02:00.0 (0000 -> 0003)
[   13.576000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   13.576000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[   13.576000] sky2 0000:02:00.0: v1.18 addr 0x54000000 irq 16 Yukon-FE (0xb7) rev 1
[   13.576000] sky2 eth0: addr 00:1b:24:27:b4:d7
[   13.856000] intel_rng: FWH not detected
[   13.896000] iTCO_vendor_support: vendor-support=0
[   13.896000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[   13.896000] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[   13.896000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   14.260000] ACPI: PCI Interrupt 0000:0a:09.2[A] -> GSI 20 (level, low) -> IRQ 19
[   14.380000] Yenta: CardBus bridge found at 0000:0a:09.0 [1025:0110]
[   14.380000] Yenta: Using CSCINT to route CSC interrupts to PCI
[   14.380000] Yenta: Routing CardBus interrupts to PCI
[   14.380000] Yenta TI: socket 0000:0a:09.0, mfunc 0x01321b22, devctl 0x66
[   14.584000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   14.584000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   14.612000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 19
[   14.612000] Socket status: 30000006
[   14.612000] Yenta: Raising subordinate bus# of parent bus (#0a) from #0b to #0e
[   14.612000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[   14.612000] cs: IO port probe 0x3000-0x3fff: clean.
[   14.612000] pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
[   14.612000] pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
[   14.976000] cs: IO port probe 0x100-0x3af: clean.
[   14.980000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   14.980000] cs: IO port probe 0x820-0x8ff: clean.
[   14.980000] cs: IO port probe 0xc00-0xcf7: clean.
[   14.980000] cs: IO port probe 0xa00-0xaff: clean.
[   14.992000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000
[   15.048000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[   16.368000] hda_intel: azx_get_response timeout, switching to polling mode...
[   16.516000] si3054: cannot initialize. EXT MID = 0000
[   16.708000] lp: driver loaded but no devices found
[   16.888000] ndiswrapper version 1.48 loaded (smp=yes, preempt=no)
[   16.976000] ndiswrapper: driver net5211 (,11/15/2006,5.1.1.9) loaded
[   16.980000] PCI: Enabling device 0000:03:00.0 (0000 -> 0002)
[   16.980000] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[   16.980000] ndiswrapper (ZwClose:2244): closing handle 0xf7421e28 not implemented
[   16.980000] PCI: Setting latency timer of device 0000:03:00.0 to 64
[   17.392000] ndiswrapper: using IRQ 17
[   17.592000] wlan0: ethernet device 00:19:7e:4c:18:55 using serialized NDIS driver: net5211, version: 0x50001, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 168C:001C.5.conf
[   17.596000] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
[   17.600000] usbcore: registered new interface driver ndiswrapper
[   17.652000] Adding 3004112k swap on /dev/sda5.  Priority:-1 extents:1 across:3004112k
[   18.032000] EXT3 FS on sda1, internal journal
[   20.032000] NET: Registered protocol family 17
[   20.300000] ACPI: Battery Slot [BAT1] (battery present)
[   20.532000] input: Power Button (FF) as /class/input/input4
[   20.536000] ACPI: Power Button (FF) [PWRF]
[   20.564000] input: Lid Switch as /class/input/input5
[   20.568000] ACPI: Lid Switch [LID]
[   20.600000] input: Power Button (CM) as /class/input/input6
[   20.604000] ACPI: Power Button (CM) [PWRB]
[   20.632000] input: Sleep Button (CM) as /class/input/input7
[   20.636000] ACPI: Sleep Button (CM) [SLPB]
[   20.672000] ACPI: AC Adapter [ACAD] (on-line)
[   20.696000] ACPI: ACPI Dock Station Driver 
[   20.744000] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   21.828000] ppdev: user-space parallel port driver
[   21.960000] sky2 eth0: enabling interface
[   22.052000] audit(1192911321.267:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4809 profile="/usr/sbin/cupsd"
[   22.112000] apm: BIOS not found.
[   22.372000] Failure registering capabilities with primary security module.
[   22.536000] Bluetooth: Core ver 2.11
[   22.536000] NET: Registered protocol family 31
[   22.536000] Bluetooth: HCI device and connection manager initialized
[   22.536000] Bluetooth: HCI socket layer initialized
[   22.552000] Bluetooth: L2CAP ver 2.8
[   22.552000] Bluetooth: L2CAP socket layer initialized
[   22.608000] Bluetooth: RFCOMM socket layer initialized
[   22.608000] Bluetooth: RFCOMM TTY layer initialized
[   22.608000] Bluetooth: RFCOMM ver 1.8
[   26.100000] [drm] Initialized drm 1.1.0 20060810
[   26.104000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[   26.104000] [drm] Initialized i915 1.6.0 20060119 on minor 0
[   80.772000] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[   86.532000] NET: Registered protocol family 10
[   86.532000] lo: Disabled Privacy Extensions
[   86.532000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   96.552000] eth0: no IPv6 routers present
[ 6569.580000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6569.580000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6569.724000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6569.724000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6569.920000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6569.920000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.060000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6570.060000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.196000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6570.196000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.308000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6570.308000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.392000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6570.392000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.500000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6570.500000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.552000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6570.552000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.644000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6570.644000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.700000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6570.700000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6570.828000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6570.828000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6576.676000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6576.676000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6577.160000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6577.160000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6577.556000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6577.556000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6577.820000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6577.820000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6578.068000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6578.068000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6578.320000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6578.320000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6578.692000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6578.692000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6579.176000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6579.176000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6579.660000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6579.660000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6580.144000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6580.144000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6580.540000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6580.540000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6580.792000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6580.792000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6581.044000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6581.044000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6581.292000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6581.292000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6581.664000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6581.664000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6582.148000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6582.148000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6582.636000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6582.636000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6583.120000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6583.120000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6583.452000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6583.452000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.280000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6586.280000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.388000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6586.388000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.416000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6586.416000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.484000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6586.484000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.552000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6586.552000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.624000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6586.624000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.676000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6586.676000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.748000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6586.748000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.800000] atkbd.c: Unknown key pressed (translated set 2, code 0xee on isa0060/serio0).
[ 6586.800000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.
[ 6586.864000] atkbd.c: Unknown key released (translated set 2, code 0xee on isa0060/serio0).
[ 6586.864000] atkbd.c: Use 'setkeycodes e06e <keycode>' to make it known.