[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003ffd0000 (usable) [ 0.000000] BIOS-e820: 000000003ffd0000 - 000000003ffde000 (ACPI data) [ 0.000000] BIOS-e820: 000000003ffde000 - 0000000040000000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000fed13000 - 00000000fed1a000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] 127MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000ff780 [ 0.000000] Entering add_active_range(0, 0, 262096) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 262096 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 262096 [ 0.000000] On node 0 totalpages: 262096 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 255 pages used for memmap [ 0.000000] HighMem zone: 32465 pages, LIFO batch:7 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP signature @ 0xC00F8110 checksum 0 [ 0.000000] ACPI: RSDP 000F8110, 0014 (r0 ACPIAM) [ 0.000000] ACPI: RSDT 3FFD0000, 003C (r1 A M I OEMRSDT 10000505 MSFT 97) [ 0.000000] ACPI: FACP 3FFD0200, 0084 (r2 A M I OEMFACP 10000505 MSFT 97) [ 0.000000] ACPI: DSDT 3FFD0430, 4A43 (r1 UW____ F18_____ 1 INTL 2002026) [ 0.000000] ACPI: FACS 3FFDE000, 0040 [ 0.000000] ACPI: APIC 3FFD0390, 0054 (r1 A M I OEMAPIC 10000505 MSFT 97) [ 0.000000] ACPI: MCFG 3FFD03F0, 003C (r1 A M I OEMMCFG 10000505 MSFT 97) [ 0.000000] ACPI: OEMB 3FFDE040, 0046 (r1 A M I AMI_OEM 10000505 MSFT 97) [ 0.000000] ACPI: MCFG 3FFD4E80, 003C (r1 A M I OEMMCFG 10000505 MSFT 97) [ 0.000000] ACPI: SSDT 3FFD4EC0, 03F6 (r1 AMI CPU1PM 1 INTL 2002026) [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] Virtual Wire compatibility mode. [ 0.000000] OEM ID: TEMPLATE Product ID: ETEMPLATE APIC at: 0xFEE00000 [ 0.000000] Processor #0 6:13 APIC version 20 [ 0.000000] I/O APIC #1 Version 32 at 0xFEC00000. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Processors: 1 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bed13000) [ 0.000000] Built 1 zonelists. Total pages: 260049 [ 0.000000] Kernel command line: root=UUID=90c89c74-adea-4faf-a1ae-3d674df2c18c ro quiet ec_intr=0 noapic nolapic pci=routeirq splash [ 0.000000] ACPI: EC: polling mode. [ 0.000000] mapped APIC to ffffd000 (fee00000) [ 0.000000] mapped IOAPIC to ffffc000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2000.130 MHz processor. [ 12.102007] Console: colour VGA+ 80x25 [ 12.102301] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 12.102678] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 12.132975] Memory: 1027640k/1048384k available (2015k kernel code, 19980k reserved, 916k data, 364k init, 130880k highmem) [ 12.132983] virtual kernel memory layout: [ 12.132984] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB) [ 12.132985] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 12.132986] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 12.132987] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 12.132988] .init : 0xc03e3000 - 0xc043e000 ( 364 kB) [ 12.132989] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB) [ 12.132991] .text : 0xc0100000 - 0xc02f7d26 (2015 kB) [ 12.132994] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 12.133026] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 12.212896] Calibrating delay using timer specific routine.. 4003.27 BogoMIPS (lpj=8006552) [ 12.212919] Security Framework v1.0.0 initialized [ 12.212926] SELinux: Disabled at boot. [ 12.212937] Mount-cache hash table entries: 512 [ 12.213045] CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 [ 12.213055] CPU: L1 I cache: 32K, L1 D cache: 32K [ 12.213058] CPU: L2 cache: 2048K [ 12.213060] CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040 00000180 00000000 00000000 [ 12.213068] Compat vDSO mapped to ffffe000. [ 12.213078] Checking 'hlt' instruction... OK. [ 12.228948] SMP alternatives: switching to UP code [ 12.229105] Freeing SMP alternatives: 11k freed [ 12.229325] Early unpacking initramfs... done [ 12.521125] ACPI: Core revision 20070126 [ 12.521184] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 12.522844] ACPI: setting ELCR to 0200 (from 0c28) [ 12.523248] CPU0: Intel(R) Pentium(R) M processor 2.00GHz stepping 08 [ 12.523268] Total of 1 processors activated (4003.27 BogoMIPS). [ 12.628168] Brought up 1 CPUs [ 12.628263] Booting paravirtualized kernel on bare hardware [ 12.628317] Time: 20:24:44 Date: 10/03/107 [ 12.628335] NET: Registered protocol family 16 [ 12.628402] EISA bus registered [ 12.628413] ACPI: bus type pci registered [ 12.628534] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3 [ 12.628536] PCI: Using configuration type 1 [ 12.628538] Setting up standard PCI resources [ 12.641543] ACPI: EC: Look up EC in DSDT [ 12.641658] ACPI: EC: GPE=0x18, ports=0x66, 0x62 [ 12.649561] ACPI: Interpreter enabled [ 12.649563] ACPI: (supports S0 S3 S4 S5) [ 12.649577] ACPI: Using PIC for interrupt routing [ 12.750330] ACPI: EC: GPE=0x18, ports=0x66, 0x62 [ 12.750410] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 12.750421] PCI: Probing PCI hardware (bus 00) [ 12.750822] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 12.750825] PCI quirk: region 0480-04bf claimed by ICH6 GPIO [ 12.751304] PCI: Transparent bridge - 0000:00:1e.0 [ 12.751339] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 12.751489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 12.751595] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT] [ 13.660653] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 13.660745] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) [ 13.660836] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) [ 13.660926] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15) [ 13.661016] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 13.661107] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 13.661198] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 13.661292] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 13.661367] Linux Plug and Play Support v0.97 (c) Adam Belay [ 13.661374] pnp: PnP ACPI init [ 13.661383] ACPI: bus type pnp registered [ 13.666622] pnp: PnP ACPI: found 12 devices [ 13.666624] ACPI: ACPI bus type pnp unregistered [ 13.666628] PnPBIOS: Disabled by ACPI PNP [ 13.666662] PCI: Using ACPI for IRQ routing [ 13.666664] PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified [ 13.666773] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 [ 13.666775] PCI: setting IRQ 10 as level-triggered [ 13.666779] ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.666783] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.666786] ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.666888] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 [ 13.666890] PCI: setting IRQ 11 as level-triggered [ 13.666894] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 13.666995] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 3 [ 13.666997] PCI: setting IRQ 3 as level-triggered [ 13.667000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 13.667101] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 [ 13.667103] PCI: setting IRQ 5 as level-triggered [ 13.667107] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 13.667110] ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.667114] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 13.667117] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 13.667120] ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 13.667124] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.667127] ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 13.667130] ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 13.667133] ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 13.667137] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.667142] PCI: Cannot allocate resource region 7 of bridge 0000:00:1e.0 [ 13.667201] PCI: Cannot allocate resource region 0 of device 0000:01:07.0 [ 13.667237] PCI: Cannot allocate resource region 1 of device 0000:01:07.0 [ 13.667273] PCI: Cannot allocate resource region 2 of device 0000:01:07.0 [ 13.667309] PCI: Cannot allocate resource region 3 of device 0000:01:07.0 [ 13.667345] PCI: Cannot allocate resource region 4 of device 0000:01:07.0 [ 13.667380] PCI: Cannot allocate resource region 5 of device 0000:01:07.0 [ 13.672411] NET: Registered protocol family 8 [ 13.672413] NET: Registered protocol family 20 [ 13.672455] pnp: 00:01: iomem range 0xfed13000-0xfed19fff could not be reserved [ 13.672461] pnp: 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 13.672464] pnp: 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved [ 13.672467] pnp: 00:08: iomem range 0xffb00000-0xffbfffff has been reserved [ 13.672470] pnp: 00:08: iomem range 0xfff80000-0xffffffff could not be reserved [ 13.672474] pnp: 00:09: iomem range 0xfec00000-0xfec00fff has been reserved [ 13.672476] pnp: 00:09: iomem range 0xfee00000-0xfee00fff has been reserved [ 13.672480] pnp: 00:0a: iomem range 0xe0000000-0xefffffff has been reserved [ 13.672484] pnp: 00:0b: iomem range 0x0-0x9ffff could not be reserved [ 13.672487] pnp: 00:0b: iomem range 0xc0000-0xcffff could not be reserved [ 13.672489] pnp: 00:0b: iomem range 0xe0000-0xfffff could not be reserved [ 13.672492] pnp: 00:0b: iomem range 0x100000-0x3fffffff could not be reserved [ 13.674179] Time: tsc clocksource has been installed. [ 13.702660] PCI: Bridge: 0000:00:01.0 [ 13.702661] IO window: disabled. [ 13.702665] MEM window: faa00000-feafffff [ 13.702668] PREFETCH window: bfe00000-dfefffff [ 13.702671] PCI: Bridge: 0000:00:1c.0 [ 13.702673] IO window: d000-dfff [ 13.702677] MEM window: bfc00000-bfcfffff [ 13.702680] PREFETCH window: bfd00000-bfdfffff [ 13.702700] PCI: Bridge: 0000:00:1e.0 [ 13.702702] IO window: 1000-1fff [ 13.702707] MEM window: fa900000-fa9fffff [ 13.702710] PREFETCH window: 50000000-500fffff [ 13.702720] ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.702725] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 13.702739] PCI: Enabling device 0000:00:1c.0 (0106 -> 0107) [ 13.702741] ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 13.702746] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 13.702755] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 13.702764] NET: Registered protocol family 2 [ 13.742077] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 13.742139] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 13.743314] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 13.743860] TCP: Hash tables configured (established 131072 bind 65536) [ 13.743863] TCP reno registered [ 13.754170] checking if image is initramfs... it is [ 14.205202] Switched to high resolution mode on CPU 0 [ 14.326809] Freeing initrd memory: 7115k freed [ 14.327149] audit: initializing netlink socket (disabled) [ 14.327162] audit(1194121484.408:1): initialized [ 14.327228] highmem bounce pool size: 64 pages [ 14.328715] VFS: Disk quotas dquot_6.5.1 [ 14.328757] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 14.328837] io scheduler noop registered [ 14.328839] io scheduler anticipatory registered [ 14.328841] io scheduler deadline registered [ 14.328854] io scheduler cfq registered (default) [ 14.352845] Boot video device is 0000:03:00.0 [ 14.352917] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 14.352944] assign_interrupt_mode Found MSI capability [ 14.352947] Allocate Port Service[0000:00:01.0:pcie00] [ 14.353005] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 14.353038] assign_interrupt_mode Found MSI capability [ 14.353040] Allocate Port Service[0000:00:1c.0:pcie00] [ 14.353063] Allocate Port Service[0000:00:1c.0:pcie02] [ 14.353175] isapnp: Scanning for PnP cards... [ 14.705642] isapnp: No Plug & Play device found [ 14.725565] Real Time Clock Driver v1.12ac [ 14.725671] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 14.726611] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 14.726788] input: Macintosh mouse button emulation as /class/input/input0 [ 14.726849] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 14.731991] i8042.c: Detected active multiplexing controller, rev 1.0. [ 14.732857] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 14.732862] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 14.732864] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 14.732866] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 14.732868] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 14.733002] mice: PS/2 mouse device common for all mice [ 14.733219] EISA: Probing bus 0 at eisa.0 [ 14.733236] Cannot allocate resource for EISA slot 1 [ 14.733255] EISA: Detected 0 cards. [ 14.733338] TCP cubic registered [ 14.733351] NET: Registered protocol family 1 [ 14.733372] Using IPI No-Shortcut mode [ 14.733846] Magic number: 15:750:446 [ 14.734132] Freeing unused kernel memory: 364k freed [ 14.796020] input: AT Translated Set 2 keyboard as /class/input/input1 [ 15.896742] AppArmor: AppArmor initialized<5>audit(1194121485.908:2): type=1505 info="AppArmor initialized" pid=1207 [ 15.903560] fuse init (API version 7.8) [ 15.907899] Failure registering capabilities with primary security module. [ 15.919665] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 15.919670] ACPI: Processor [CPU1] (supports 8 throttling states) [ 15.921258] ACPI: Thermal Zone [THRM] (28 C) [ 16.261214] usbcore: registered new interface driver usbfs [ 16.261235] usbcore: registered new interface driver hub [ 16.261251] usbcore: registered new device driver usb [ 16.261894] USB Universal Host Controller Interface driver v3.0 [ 16.261951] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 16.261961] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 16.261965] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 16.262128] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 16.262152] uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000e480 [ 16.262239] usb usb1: configuration #1 chosen from 1 choice [ 16.262262] hub 1-0:1.0: USB hub found [ 16.262267] hub 1-0:1.0: 2 ports detected [ 16.336055] SCSI subsystem initialized [ 16.340405] libata version 2.21 loaded. [ 16.365028] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 16.365039] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 16.365043] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 16.365065] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 16.365090] uhci_hcd 0000:00:1d.1: irq 3, io base 0x0000e800 [ 16.365172] usb usb2: configuration #1 chosen from 1 choice [ 16.365193] hub 2-0:1.0: USB hub found [ 16.365199] hub 2-0:1.0: 2 ports detected [ 16.468848] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 16.468861] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 16.468865] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 16.468887] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 16.468912] uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000e880 [ 16.468990] usb usb3: configuration #1 chosen from 1 choice [ 16.469015] hub 3-0:1.0: USB hub found [ 16.469020] hub 3-0:1.0: 2 ports detected [ 16.572623] ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 16.572635] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 16.572639] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 16.572659] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 16.572684] uhci_hcd 0000:00:1d.3: irq 10, io base 0x0000ec00 [ 16.572764] usb usb4: configuration #1 chosen from 1 choice [ 16.572787] hub 4-0:1.0: USB hub found [ 16.572792] hub 4-0:1.0: 2 ports detected [ 3.816000] Marking TSC unstable due to: possible TSC halt in C2. [ 3.820000] Time: acpi_pm clocksource has been installed. [ 3.916000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 3.916000] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 3.916000] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 3.916000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 3.916000] ehci_hcd 0000:00:1d.7: debug port 1 [ 3.916000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 3.916000] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xfebffc00 [ 3.920000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 3.920000] usb usb5: configuration #1 chosen from 1 choice [ 3.920000] hub 5-0:1.0: USB hub found [ 3.920000] hub 5-0:1.0: 8 ports detected [ 4.024000] ata_piix 0000:00:1f.1: version 2.11 [ 4.024000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 4.024000] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 4.024000] scsi0 : ata_piix [ 4.036000] scsi1 : ata_piix [ 4.036000] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14 [ 4.036000] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15 [ 4.356000] ata1.00: ATAPI: HL-DT-ST DVD-RW GWA-4082N, CW02, max UDMA/33 [ 4.528000] ata1.00: configured for UDMA/33 [ 4.696000] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD-RW GWA-4082N CW02 PQ: 0 ANSI: 5 [ 4.696000] ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 4.748000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[fa9ff000-fa9ff7ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 4.752000] r8169 Gigabit Ethernet driver 2.2LK loaded [ 4.752000] ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 4.752000] eth0: RTL8169sb/8110sb at 0xf8856c00, 00:03:0d:36:83:c8, XID 10000000 IRQ 3 [ 4.756000] sata_via 0000:01:07.0: version 2.2 [ 4.756000] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 4.756000] sata_via 0000:01:07.0: routed to hard irq line 10 [ 4.756000] scsi2 : sata_via [ 4.756000] scsi3 : sata_via [ 4.756000] scsi4 : sata_via [ 4.756000] ata3: SATA max UDMA/133 cmd 0x00011420 ctl 0x0001142a bmdma 0x00011400 irq 10 [ 4.756000] ata4: SATA max UDMA/133 cmd 0x00011430 ctl 0x0001143a bmdma 0x00011408 irq 10 [ 4.756000] ata5: PATA max UDMA/133 cmd 0x00011440 ctl 0x0001144a bmdma 0x00011410 irq 10 [ 4.772000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray [ 4.772000] Uniform CD-ROM driver Revision: 3.20 [ 4.772000] sr 0:0:0:0: Attached scsi CD-ROM sr0 [ 4.776000] sr 0:0:0:0: Attached scsi generic sg0 type 5 [ 5.224000] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 5.232000] ata3.00: ATA-7: FUJITSU MHT2080BH, 0000104B, max UDMA/100 [ 5.232000] ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 5.248000] ata3.00: configured for UDMA/100 [ 5.716000] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 5.724000] ata4.00: ATA-7: FUJITSU MHT2080BH, 0000104B, max UDMA/100 [ 5.724000] ata4.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 5.740000] ata4.00: configured for UDMA/100 [ 5.904000] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHT2080B 0000 PQ: 0 ANSI: 5 [ 5.904000] scsi 2:0:0:0: Attached scsi generic sg1 type 0 [ 5.904000] scsi 3:0:0:0: Direct-Access ATA FUJITSU MHT2080B 0000 PQ: 0 ANSI: 5 [ 5.908000] scsi 3:0:0:0: Attached scsi generic sg2 type 0 [ 5.916000] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 5.916000] sd 2:0:0:0: [sda] Write Protect is off [ 5.916000] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.916000] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.916000] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 5.916000] sd 2:0:0:0: [sda] Write Protect is off [ 5.916000] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.916000] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.916000] sda: sda1 sda2 sda3 [ 5.976000] sd 2:0:0:0: [sda] Attached SCSI disk [ 5.976000] sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB) [ 5.976000] sd 3:0:0:0: [sdb] Write Protect is off [ 5.976000] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 5.976000] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.976000] sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB) [ 5.976000] sd 3:0:0:0: [sdb] Write Protect is off [ 5.976000] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 5.976000] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.976000] sdb:<7>ieee1394: Host added: ID:BUS[0-00:1023] GUID[00030d4971e309f2] [ 6.020000] sdb1 [ 6.020000] sd 3:0:0:0: [sdb] Attached SCSI disk [ 6.408000] Attempting manual resume [ 6.408000] swsusp: Resume From Partition 8:2 [ 6.408000] PM: Checking swsusp image. [ 6.408000] PM: Resume from disk failed. [ 6.448000] kjournald starting. Commit interval 5 seconds [ 6.448000] EXT3-fs: mounted filesystem with ordered data mode. [ 15.920000] Linux agpgart interface v0.102 (c) Dave Jones [ 15.948000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 15.952000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 16.452000] ieee80211_crypt: registered algorithm 'NULL' [ 16.644000] intel_rng: FWH not detected [ 16.652000] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 16.652000] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 16.948000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq [ 16.948000] ipw2200: Copyright(c) 2003-2006 Intel Corporation [ 16.948000] ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 16.948000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection [ 16.952000] iTCO_vendor_support: vendor-support=0 [ 16.952000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007) [ 16.952000] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x0860) [ 16.952000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 17.000000] nvidia: module license 'NVIDIA' taints kernel. [ 17.436000] input: PC Speaker as /class/input/input2 [ 17.844000] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels) [ 17.844000] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 17.844000] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 17.844000] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007 [ 17.884000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 17.884000] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 17.960000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x6eb1, caps: 0xa04711/0x40a [ 17.996000] input: SynPS/2 Synaptics TouchPad as /class/input/input3 [ 18.704000] lp: driver loaded but no devices found [ 18.768000] Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k [ 19.292000] EXT3 FS on sda3, internal journal [ 21.024000] No dock devices found. [ 21.096000] input: Power Button (FF) as /class/input/input4 [ 21.100000] ACPI: Power Button (FF) [PWRF] [ 21.136000] input: Lid Switch as /class/input/input5 [ 21.140000] ACPI: Lid Switch [LID] [ 21.176000] input: Sleep Button (CM) as /class/input/input6 [ 21.180000] ACPI: Sleep Button (CM) [SLPB] [ 21.216000] input: Power Button (CM) as /class/input/input7 [ 21.216000] ACPI: Power Button (CM) [PWRB] [ 21.340000] ACPI Error (utglobal-0126): Unknown exception code: 0xFFFFFFFE [20070126] [ 21.340000] ACPI Exception (video-1647): UNKNOWN_STATUS_CODE, Cant attach device [20070126] [ 21.340000] ACPI: Video Device [PEG] (multi-head: yes rom: no post: no) [ 21.380000] ACPI: AC Adapter [AC0] (on-line) [ 21.448000] ACPI: Battery Slot [BAT0] (battery present) [ 23.076000] r8169: eth2: link up [ 23.300000] NET: Registered protocol family 10 [ 23.300000] lo: Disabled Privacy Extensions [ 23.300000] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 23.900000] ppdev: user-space parallel port driver [ 24.056000] audit(1194121508.223:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=4970 profile="/usr/sbin/cupsd" [ 24.140000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 24.140000] apm: overridden by ACPI. [ 25.936000] Clocksource tsc unstable (delta = -300006333 ns) [ 26.544000] Failure registering capabilities with primary security module. [ 26.892000] Bluetooth: Core ver 2.11 [ 26.892000] NET: Registered protocol family 31 [ 26.892000] Bluetooth: HCI device and connection manager initialized [ 26.892000] Bluetooth: HCI socket layer initialized [ 26.936000] Bluetooth: L2CAP ver 2.8 [ 26.936000] Bluetooth: L2CAP socket layer initialized [ 27.048000] Bluetooth: RFCOMM socket layer initialized [ 27.048000] Bluetooth: RFCOMM TTY layer initialized [ 27.048000] Bluetooth: RFCOMM ver 1.8 [ 28.152000] r8169: eth2: link down [ 29.808000] r8169: eth2: link up [ 29.932000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 30.252000] r8169: eth2: link down [ 32.060000] NET: Registered protocol family 17 [ 32.640000] r8169: eth2: link up [ 32.644000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 33.348000] /dev/vmmon[5622]: Module vmmon: registered with major=10 minor=165 [ 33.348000] /dev/vmmon[5622]: Module vmmon: initialized [ 33.720000] /dev/vmnet: open called by PID 5653 (vmnet-bridge) [ 33.720000] /dev/vmnet: hub 0 does not exist, allocating memory. [ 33.720000] /dev/vmnet: port on hub 0 successfully opened [ 33.724000] bridge-eth1: enabling the bridge [ 33.724000] bridge-eth1: up [ 33.724000] bridge-eth1: already up [ 33.724000] bridge-eth1: attached [ 33.724000] /dev/vmnet: open called by PID 5663 (vmnet-bridge) [ 33.724000] /dev/vmnet: hub 2 does not exist, allocating memory. [ 33.724000] /dev/vmnet: port on hub 2 successfully opened [ 33.724000] bridge-eth2: enabling the bridge [ 33.724000] bridge-eth2: up [ 33.724000] bridge-eth2: already up [ 33.724000] bridge-eth2: attached [ 33.784000] /dev/vmnet: open called by PID 5672 (vmnet-natd) [ 33.788000] /dev/vmnet: hub 8 does not exist, allocating memory. [ 33.788000] /dev/vmnet: port on hub 8 successfully opened [ 33.808000] /dev/vmnet: open called by PID 5673 (vmnet-netifup) [ 33.808000] /dev/vmnet: hub 1 does not exist, allocating memory. [ 33.808000] /dev/vmnet: port on hub 1 successfully opened [ 33.812000] /dev/vmnet: open called by PID 5674 (vmnet-netifup) [ 33.812000] /dev/vmnet: port on hub 8 successfully opened [ 34.424000] /dev/vmnet: open called by PID 5710 (vmnet-dhcpd) [ 34.424000] /dev/vmnet: port on hub 8 successfully opened [ 34.948000] /dev/vmnet: open called by PID 5709 (vmnet-dhcpd) [ 34.952000] /dev/vmnet: port on hub 1 successfully opened [ 44.304000] vmnet8: no IPv6 routers present [ 44.712000] vmnet1: no IPv6 routers present [ 49.908000] eth2: no IPv6 routers present [ 59.540000] r8169: eth2: link down [ 87.816000] r8169: eth2: link up [ 87.820000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 101.892000] eth2: no IPv6 routers present [ 384.040000] r8169: eth2: link down [ 385.740000] r8169: eth2: link up [ 385.744000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 401.028000] eth2: no IPv6 routers present [ 452.424000] r8169: eth2: link down [ 454.096000] r8169: eth2: link up [ 454.100000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 469.532000] eth2: no IPv6 routers present [ 636.840000] r8169: eth2: link down [ 641.376000] r8169: eth2: link up [ 641.380000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 644.476000] r8169: eth2: link down [ 646.128000] r8169: eth2: link up [ 646.132000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 662.084000] eth2: no IPv6 routers present [ 720.408000] r8169: eth2: link down [ 722.072000] r8169: eth2: link up [ 722.072000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 737.472000] eth2: no IPv6 routers present [ 910.264000] spurious 8259A interrupt: IRQ7. [ 1015.580000] r8169: eth2: link down [ 1017.272000] r8169: eth2: link up [ 1017.276000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 1031.492000] eth2: no IPv6 routers present [ 1211.212000] r8169: eth2: link down [ 1212.808000] r8169: eth2: link up [ 1212.812000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 1222.504000] r8169: eth2: link down [ 1222.840000] eth2: no IPv6 routers present [ 1224.164000] r8169: eth2: link up [ 1224.168000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 1238.812000] eth2: no IPv6 routers present [ 2126.984000] r8169: eth2: link down [ 2128.660000] r8169: eth2: link up [ 2128.664000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 2140.516000] r8169: eth2: link down [ 2142.144000] r8169: eth2: link up [ 2142.148000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 2143.792000] r8169: eth2: link down [ 2145.592000] r8169: eth2: link up [ 2145.596000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 2160.088000] eth2: no IPv6 routers present [ 2183.052000] r8169: eth2: link down [ 2184.656000] r8169: eth2: link up [ 2184.660000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 2201.416000] eth2: no IPv6 routers present [ 2229.904000] r8169: eth2: link down [ 2233.996000] r8169: eth2: link up [ 2233.996000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 2248.660000] eth2: no IPv6 routers present [ 5348.504000] r8169: eth2: link down [ 5350.112000] r8169: eth2: link up [ 5350.116000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 5352.120000] r8169: eth2: link down [ 5366.576000] r8169: eth2: link up [ 5366.580000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 5366.996000] r8169: eth2: link down [ 5371.160000] r8169: eth2: link up [ 5371.164000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 5389.016000] eth2: no IPv6 routers present [ 6326.128000] r8169: eth2: link down [ 6328.116000] r8169: eth2: link up [ 6328.116000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 6345.180000] eth2: no IPv6 routers present [ 8438.960000] bridge-eth1: disabling the bridge [ 8438.968000] bridge-eth1: down [ 8438.996000] bridge-eth2: disabling the bridge [ 8439.008000] bridge-eth2: down [ 8439.808000] ACPI: PCI interrupt for device 0000:01:03.0 disabled [ 8439.856000] ieee80211_crypt: unregistered algorithm 'NULL' [ 8440.020000] ACPI: PCI interrupt for device 0000:01:05.0 disabled [ 8442.124000] PM: suspend-to-disk mode set to 'shutdown' [ 8442.124000] swsusp: Basic memory bitmaps created [ 8442.124000] Stopping tasks ... done. [ 8442.448000] Shrinking memory... -\|/-\|/-done (101126 pages freed) [ 8443.496000] Freed 404504 kbytes in 1.04 seconds (388.94 MB/s) [ 8443.496000] Suspending console(s) [ 8443.496000] sd 3:0:0:0: [sdb] Synchronizing SCSI cache [ 8443.700000] sd 2:0:0:0: [sda] Synchronizing SCSI cache [ 8443.700000] usb_device usbdev5.1: PM: suspend 0->1, parent usb5 already 2 [ 8443.700000] usb_endpoint usbdev5.1_ep81: PM: suspend 0->1, parent 5-0:1.0 already 2 [ 8443.700000] hub 5-0:1.0: PM: suspend 2->1, parent usb5 already 2 [ 8443.700000] usb_endpoint usbdev5.1_ep00: PM: suspend 0->1, parent usb5 already 2 [ 8443.700000] usb_device usbdev4.1: PM: suspend 0->1, parent usb4 already 2 [ 8443.700000] usb_endpoint usbdev4.1_ep81: PM: suspend 0->1, parent 4-0:1.0 already 2 [ 8443.700000] hub 4-0:1.0: PM: suspend 2->1, parent usb4 already 2 [ 8443.700000] usb_endpoint usbdev4.1_ep00: PM: suspend 0->1, parent usb4 already 2 [ 8443.700000] usb_device usbdev3.1: PM: suspend 0->1, parent usb3 already 2 [ 8443.700000] usb_endpoint usbdev3.1_ep81: PM: suspend 0->1, parent 3-0:1.0 already 2 [ 8443.700000] hub 3-0:1.0: PM: suspend 2->1, parent usb3 already 2 [ 8443.700000] usb_endpoint usbdev3.1_ep00: PM: suspend 0->1, parent usb3 already 2 [ 8443.700000] usb_device usbdev2.1: PM: suspend 0->1, parent usb2 already 2 [ 8443.700000] usb_endpoint usbdev2.1_ep81: PM: suspend 0->1, parent 2-0:1.0 already 2 [ 8443.700000] hub 2-0:1.0: PM: suspend 2->1, parent usb2 already 2 [ 8443.700000] usb_endpoint usbdev2.1_ep00: PM: suspend 0->1, parent usb2 already 2 [ 8443.700000] usb_device usbdev1.1: PM: suspend 0->1, parent usb1 already 2 [ 8443.700000] usb_endpoint usbdev1.1_ep81: PM: suspend 0->1, parent 1-0:1.0 already 2 [ 8443.700000] hub 1-0:1.0: PM: suspend 2->1, parent usb1 already 2 [ 8443.700000] usb_endpoint usbdev1.1_ep00: PM: suspend 0->1, parent usb1 already 2 [ 8443.700000] ACPI: PCI interrupt for device 0000:01:07.0 disabled [ 8443.716000] NVRM: RmPowerManagement: 3 [ 8445.292000] ACPI: PCI interrupt for device 0000:00:1f.1 disabled [ 8445.292000] ACPI: PCI interrupt for device 0000:00:1d.7 disabled [ 8445.308000] ACPI: PCI interrupt for device 0000:00:1d.3 disabled [ 8445.308000] ACPI: PCI interrupt for device 0000:00:1d.2 disabled [ 8445.308000] ACPI: PCI interrupt for device 0000:00:1d.1 disabled [ 8445.308000] ACPI: PCI interrupt for device 0000:00:1d.0 disabled [ 8445.316000] ACPI: PCI interrupt for device 0000:00:1b.0 disabled [ 8445.332000] Disabling non-boot CPUs ... [ 8445.332000] PM: snapshotting memory. [ 8445.332000] swsusp: critical section: [ 8445.332000] swsusp: Need to copy 126021 pages [ 8445.332000] swsusp: Normal pages needed: 113637 + 1024 + 24, available pages: 123682 [ 8445.332000] PM: Image restored successfully. [ 8445.332000] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 8445.348000] PM: Writing back config space on device 0000:00:1b.0 at offset 1 (was 100006, writing 100002) [ 8445.348000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 8445.348000] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 8445.440000] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 8445.440000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 8445.440000] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 8445.440000] usb usb1: root hub lost power or was reset [ 8445.440000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 8445.440000] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 8445.440000] usb usb2: root hub lost power or was reset [ 8445.440000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 8445.440000] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 8445.440000] usb usb3: root hub lost power or was reset [ 8445.440000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 8445.440000] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 8445.440000] usb usb4: root hub lost power or was reset [ 8445.456000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 8445.456000] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 8445.456000] usb usb5: root hub lost power or was reset [ 8445.456000] ehci_hcd 0000:00:1d.7: debug port 1 [ 8445.456000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 8445.456000] PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100107, writing 20100107) [ 8445.460000] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 8445.460000] PM: Writing back config space on device 0000:00:1f.1 at offset 1 (was 2880001, writing 2880005) [ 8445.460000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 [ 8445.460000] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 8445.460000] NVRM: RmPowerManagement: 4 [ 8447.580000] PM: Writing back config space on device 0000:01:03.0 at offset 1 (was 2900016, writing 2900002) [ 8447.596000] PM: Writing back config space on device 0000:01:04.0 at offset f (was 4030100, writing 4030105) [ 8447.596000] PM: Writing back config space on device 0000:01:04.0 at offset 5 (was 0, writing fa9f8000) [ 8447.596000] PM: Writing back config space on device 0000:01:04.0 at offset 4 (was 0, writing fa9ff000) [ 8447.596000] PM: Writing back config space on device 0000:01:04.0 at offset 3 (was 0, writing 4008) [ 8447.596000] PM: Writing back config space on device 0000:01:04.0 at offset 1 (was 2100000, writing 2100016) [ 8447.644000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[5] MMIO=[fa9ff000-fa9ff7ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 8447.644000] PM: Writing back config space on device 0000:01:05.0 at offset 1 (was 2b80017, writing 2b00013) [ 8447.644000] PM: Writing back config space on device 0000:01:07.0 at offset 1 (was 2900003, writing 2900007) [ 8447.644000] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 [ 8447.644000] pnp: Failed to activate device 00:04. [ 8447.644000] pnp: Failed to activate device 00:05. [ 8447.760000] ata1.00: configured for UDMA/33 [ 8448.112000] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 8448.112000] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 8448.136000] ata3.00: configured for UDMA/100 [ 8448.136000] sd 2:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) [ 8448.136000] sd 2:0:0:0: [sda] Write Protect is off [ 8448.136000] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8448.136000] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8448.136000] ata4.00: configured for UDMA/100 [ 8448.136000] sd 3:0:0:0: [sdb] 156301488 512-byte hardware sectors (80026 MB) [ 8448.136000] sd 3:0:0:0: [sdb] Write Protect is off [ 8448.136000] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 8448.136000] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8448.436000] sd 2:0:0:0: [sda] Starting disk [ 8448.476000] sd 3:0:0:0: [sdb] Starting disk [ 8448.800000] Restarting tasks ... done. [ 8449.140000] swsusp: Basic memory bitmaps freed [ 8453.668000] ieee80211_crypt: registered algorithm 'NULL' [ 8453.704000] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 8453.704000] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 8453.908000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.0kmprq [ 8453.908000] ipw2200: Copyright(c) 2003-2006 Intel Corporation [ 8453.908000] ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 8453.908000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection [ 8454.212000] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels) [ 8454.264000] r8169 Gigabit Ethernet driver 2.2LK loaded [ 8454.264000] ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKD] -> GSI 3 (level, low) -> IRQ 3 [ 8454.264000] eth0: RTL8169sb/8110sb at 0xf8a0ec00, 00:03:0d:36:83:c8, XID 10000000 IRQ 3 [ 8454.492000] bridge-eth1: enabling the bridge [ 8454.492000] bridge-eth1: up [ 8454.572000] r8169: eth2: link down [ 8454.572000] ADDRCONF(NETDEV_UP): eth2: link is not ready [ 8454.572000] bridge-eth2: enabling the bridge [ 8454.572000] bridge-eth2: up [ 8455.884000] r8169: eth2: link up [ 8456.908000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 8457.488000] input: Power Button (FF) as /class/input/input8 [ 8457.488000] ACPI: Power Button (FF) [PWRF] [ 8457.488000] input: Lid Switch as /class/input/input9 [ 8457.488000] ACPI: Lid Switch [LID] [ 8457.488000] input: Sleep Button (CM) as /class/input/input10 [ 8457.488000] ACPI: Sleep Button (CM) [SLPB] [ 8457.488000] input: Power Button (CM) as /class/input/input11 [ 8457.488000] ACPI: Power Button (CM) [PWRB] [ 8457.556000] ACPI: Thermal Zone [THRM] (29 C) [ 8457.792000] ACPI: AC Adapter [AC0] (on-line) [ 8457.928000] ACPI: Battery Slot [BAT0] (battery present) [ 8472.960000] eth2: no IPv6 routers present [ 9306.172000] r8169: eth2: link down [ 9310.284000] r8169: eth2: link up [ 9310.288000] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 9324.164000] eth2: no IPv6 routers present