Linux version 2.6.23-gentoo-r2 (root@boxy) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 SMP Tue Nov 20 04:58:55 PST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009d000 (usable) BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003bff0000 (usable) BIOS-e820: 000000003bff0000 - 000000003bff3000 (ACPI NVS) BIOS-e820: 000000003bff3000 - 000000003c000000 (ACPI data) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. found SMP MP-table at 000f3f50 Entering add_active_range(0, 0, 229376) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 229376 On node 0 totalpages: 229376 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 Movable zone: 0 pages used for memmap DMI 2.3 present. Using APIC driver default ACPI: RSDP 000F8020, 0014 (r0 CX700 ) ACPI: RSDT 3BFF3040, 0030 (r1 CX700 AWRDACPI 42302E31 AWRD 0) ACPI: FACP 3BFF30C0, 0074 (r1 CX700 AWRDACPI 42302E31 AWRD 0) ACPI: DSDT 3BFF3180, 5DD3 (r1 CX700 AWRDACPI 1000 MSFT 3000000) ACPI: FACS 3BFF0000, 0040 ACPI: MCFG 3BFF9080, 003C (r1 CX700 AWRDACPI 42302E31 AWRD 0) ACPI: APIC 3BFF8FC0, 005A (r1 CX700 AWRDACPI 42302E31 AWRD 0) ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:10 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 40000000 (gap: 3c000000:a4000000) Built 1 zonelists in Zone order. Total pages: 227584 Kernel command line: root=/dev/md2 mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1199.759 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 903988k/917504k available (2831k kernel code, 13068k reserved, 1359k data, 264k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffb4000 - 0xfffff000 ( 300 kB) vmalloc : 0xf8800000 - 0xfffb2000 ( 119 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc051f000 - 0xc0561000 ( 264 kB) .data : 0xc03c3f44 - 0xc0517dac (1359 kB) .text : 0xc0100000 - 0xc03c3f44 (2831 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2401.44 BogoMIPS (lpj=4802898) Mount-cache hash table entries: 512 CPU: After generic identify, caps: a7c9baff 00100000 00000000 00000000 00000181 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 128K (64 bytes/line) CPU: After all inits, caps: 27c9baff 00100000 00000000 00000000 00000181 00003fcc 00000000 00000000 Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 18k freed ACPI: Core revision 20070126 Parsing all Control Methods: Table [DSDT](id 0001) - 850 Objects with 89 Devices 188 Methods 45 Regions tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired evxfevnt-0091 [00] enable : Transition to ACPI mode successful CPU0: Centaur VIA Esther processor 1200MHz stepping 09 Total of 1 processors activated (2401.44 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 Brought up 1 CPUs NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on device 00:00 PCI: No mmconfig possible on device 00:01 PCI: No mmconfig possible on device 00:0f PCI: No mmconfig possible on device 00:10 PCI: No mmconfig possible on device 00:11 PCI: No mmconfig possible on device 00:13 PCI: No mmconfig possible on device 01:00 PCI: No mmconfig possible on device 02:05 PCI: No mmconfig possible on device 02:08 Setting up standard PCI resources evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int 0x9 evgpeblk-0956 [00] ev_create_gpe_block : GPE 10 to 1F [_GPE] 2 regs on int 0x9 evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 0 Runtime GPEs in this block evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 1 Wake, Enabled 1 Runtime GPEs in this block ACPI: EC: Look up EC in DSDT Completing Region/Field/Buffer/Package initialization:............................................................................................................................ Initialized 30/45 Regions 38/38 Fields 27/27 Buffers 29/35 Packages (859 nodes) Initializing Device/Processor/Thermal objects by executing _INI methods:.. Executed 2 _INI methods requiring 1 _STA executions (examined 93 objects) ACPI: Interpreter enabled ACPI: (supports S0 S1 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:13.1 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PB._PRT] ACPI: PCI Root Bridge [PCI1] (0000:80) ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 11 12) *5 ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 13 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 2.21 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Time: tsc clocksource has been installed. pnp: 00:01: ioport range 0x400-0x47f has been reserved pnp: 00:01: ioport range 0x500-0x50f has been reserved pnp: 00:09: iomem range 0xf0000000-0xf0000fff has been reserved pnp: 00:0a: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:0c: iomem range 0xf0000-0xfffff could not be reserved pnp: 00:0c: iomem range 0x3bff0000-0x3bffffff could not be reserved pnp: 00:0c: iomem range 0xffff0000-0xffffffff could not be reserved pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: dd000000-deffffff PREFETCH window: a0000000-bfffffff PCI: Bridge: 0000:00:13.1 IO window: d000-dfff MEM window: dfe00000-dfefffff PREFETCH window: dfd00000-dfdfffff PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Setting latency timer of device 0000:00:13.1 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered eps: Detected VIA Eden eps: Current voltage = 860mV eps: Current multiplier = 12 eps: Highest voltage = 860mV eps: Highest multiplier = 12 eps: Lowest voltage = 844mV eps: Lowest multiplier = 4 microcode: CPU0 not a capable Intel processor IA-32 Microcode Update Driver: v1.14a Total HugeTLB memory allocated, 0 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.28 [Flags: R/W DEBUG]. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: VIA PCI bridge detected. Disabling DAC. Boot video device is 0000:01:00.0 Real Time Clock Driver v1.12ac VIA RNG detected Linux agpgart interface v0.102 agpgart: Detected VIA CX700 chipset agpgart: AGP aperture is 128M @ 0xd0000000 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using get_cycles(). input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] ACPI: Fan [FAN] (on) ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 2 throttling states) ACPI: Thermal Zone [THRM] (40 C) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is unknown type 15 (usb?), fd1 is unknown type 15 (usb?) Marking TSC unstable due to: possible TSC halt in C2. Time: acpi_pm clocksource has been installed. Switched to high resolution mode on CPU 0 floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.14 Copyright (c) 2002, 2003 VIA Networking Technologies, Inc. Copyright (c) 2004 Red Hat Inc. ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 18 (level, low) -> IRQ 16 eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter eth0: Ethernet Address: 00:30:18:A7:DD:F4 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. 3ware Storage Controller device driver for Linux v1.26.02.002. pata_via 0000:00:0f.0: version 0.3.2 ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 21 (level, low) -> IRQ 17 scsi0 : pata_via scsi1 : pata_via ata1: PATA max UDMA/133 cmd 0x0001ff00 ctl 0x0001fe02 bmdma 0x0001fb00 irq 17 ata2: PATA max UDMA/133 cmd 0x0001fd00 ctl 0x0001fc02 bmdma 0x0001fb08 irq 17 ata1.00: ATA-7: ST3500320AS, SD04, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.01: ATA-7: ST3500320AS, SD04, max UDMA/133 ata1.01: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: limited to UDMA/33 due to 40-wire cable ata1.01: limited to UDMA/33 due to 40-wire cable ata1.00: configured for UDMA/33 ata1.01: failed to set xfermode (err_mask=0x1) ata1: failed to recover some devices, retrying in 5 secs ata1.00: configured for UDMA/33 ata1.01: failed to set xfermode (err_mask=0x1) ata1.01: limiting speed to UDMA/33:PIO3 ata1: failed to recover some devices, retrying in 5 secs ata1.00: configured for UDMA/33 ata1.01: failed to set xfermode (err_mask=0x1) ata1.01: disabled ata1: failed to recover some devices, retrying in 5 secs ata1.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA ST3500320AS SD04 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 usbmon: debugfs is not available ACPI: PCI Interrupt 0000:00:10.4[D] -> GSI 23 (level, low) -> IRQ 18 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: debug port 1 ehci_hcd 0000:00:10.4: irq 18, io mem 0xdffff000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 19 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 19, io base 0x0000fa00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 22 (level, low) -> IRQ 20 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 20, io base 0x0000f900 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 17 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 17, io base 0x0000f800 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: raid1 personality registered for level 1 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Using IPI No-Shortcut mode md: Autodetecting RAID arrays. md: autorun ... md: considering sda3 ... md: adding sda3 ... md: sda1 has different UUID to sda3 md: created md2 md: bind md: running: raid1: raid set md2 active with 1 out of 1 mirrors md: considering sda1 ... md: adding sda1 ... md: created md1 md: bind md: running: raid1: raid set md1 active with 1 out of 1 mirrors md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 264k freed EXT3 FS on md2, internal journal Unable to find swap-space signature Velocity is AUTO mode ADDRCONF(NETDEV_UP): eth0: link is not ready eth0: Link auto-negotiation speed 100M bps full duplex ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present