Marvell>> help
?       - alias for 'help'
FSdel   - del a file from the Flash MV FS
FSdir   - ls the Flash MV FS
FSformat- format the Flash MV FS
FSlef   - Load an exe file to the Flash MV FS
FSlf    - Load a file to the Flash MV FS
FSrun   - Load an exe file from the Flash MV FS and run it
FStftp  - tftp a file to the Flash MV FS
FStftpe - tftp an exe file to the Flash MV FS
FStype  - cat file from the Flash MV FS
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootext2    dev:boot_part1,boot_part2 addr boot_image linux_dev_name
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
bootvx  - Boot vxWorks from an ELF image
bubt    - Burn an image on the Boot Flash.
chpart  - change active partition
cmp     - memory compare
cmpm    - Compare Memory
coninfo - print console devices and informations
cp      - memory copy
cpumap - Display CPU memory mapping settings.
crc32   - checksum calculation
date    - get/set/reset date & time
dclk    - Display the MV device CLKs.
ddimm  - Display SPD Dimm Info
dhcp    - invoke DHCP client to obtain IP/boot params
diskboot- boot from IDE device
dma     - Perform DMA
echo    - echo args to console
eeprom  - EEPROM sub-system
erase   - erase FLASH memory
ext2load- load binary file from a Ext2 filesystem
ext2ls- list files in a directory (default /)
fi      - Find value in the memory.
flinfo  - print FLASH memory information
fsinfo  - print information about filesystems
fsload  - load binary file from a filesystem image
g       - start application at cached address 'addr'(default addr 0x40000)
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
ide     - IDE sub-system
iloop   - infinite loop on address range
imd     - i2c memory display
iminfo  - print header information for application image
imm     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
ir      - reading and changing MV internal register values.
ln      - Load S-Record executable file through the network interface.
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loop    - infinite loop on address range
ls      - list files in a directory (default /)
map     - Diasplay address decode windows
md      - memory display
me      - PCI master enable
mm      - memory modify (auto-incrementing)
mp      - map PCI BAR
mtest   - simple RAM test
mw      - memory write (fill)
nm      - memory modify (constant address)
pci     - list and access PCI Configuraton Space
phyRead - Read Phy register
phyWrite        - Write Phy register
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
resetenv        - Return all environment variable to default.
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
se      - PCI Slave enable
setenv  - set environment variables
sg      - scanning the PHYs status
sleep   - delay execution for some time
sp      - Scan PCI bus.
tftpboot- boot image via network using TFTP protocol
version - print monitor version