# dmesg Linux version 2.6.9-intc1plus-cisco (embedded@cse-dhcp-10-133.ucsd.edu) (gcc version 3.3.2) #1 Tue Dec 4 11:21:12 PST 2007 CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE) CPU: D undefined 5 cache CPU: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Machine: Intel HCDDBBVA0 Development Platform (aka Mainstone) Memory policy: ECC disabled, Data cache writeback Run Mode clock: 78.00MHz (*6) Turbo Mode clock: 78.00MHz (*1.0, active) Memory clock: 78.00MHz (/1) System bus clock: 78.00MHz On node 0 totalpages: 32768 DMA zone: 32768 pages, LIFO batch:8 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=/dev/mtdblock2 rootfstype=jffs2 ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M Relocating machine vectors to 0xffff0000 IRQ8 (GPIO0): falling edges PID hash table entries: 1024 (order: 10, 16384 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB = 128MB total Memory: 126848KB available (2301K code, 481K data, 100K init) Calibrating delay loop... 77.61 BogoMIPS (lpj=388096) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 SCSI subsystem initialized Linux Kernel Card Services options: [pm] usbcore: registered new driver hub NET: Registered protocol family 23 Register device ipmc successgul. <6>JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc. Console: switching to colour frame buffer device 30x40 Load PXA Overlay driver successfully! SA1100 Real Time Clock driver v1.00 SA1100/PXA2xx Watchdog Timer: timer margin 60 sec ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART smc91x.c: v1.0, mar 07 2003 by Nicolas Pitre eth0: SMC91C11xFD (rev 1) at 0xc8892300 IRQ 163 DMA 16 [nowait] eth0: Ethernet addr: 00:0e:0c:80:79:02 eth0: PHY LAN83C183 (LAN91C111 Internal) pxa_ir: irda driver inited Linux video capture interface: v1.00 PXA_CAMERA: PXA Camera driver loaded for: /dev/video0 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx Using anticipatory io scheduler Probing Intel PXA27x On-Chip ROM at physical address 0x00000000 (32-bit bankwidth) Intel PXA27x On-Chip ROM: Found 2 x16 devices at 0x0 in 32-bit bank Intel/Sharp Extended Query Table at 0x010A cfi_cmdset_0001: Erase suspend on write enabled 0: offset=0x0,size=0x10000,blocks=4 1: offset=0x40000,size=0x40000,blocks=255 Using buffer write method Intel PXA27x On-Chip ROM: 1 sets of 2 interleaved chips --> 16 partitions of 0x400000 bytes No RedBoot partition table detected in Intel PXA27x On-Chip ROM cmdlinepart partition parsing not available Using static partitions on Intel PXA27x On-Chip ROM Creating 3 MTD partitions on "Intel PXA27x On-Chip ROM": 0x00000000-0x00040000 : "Bootloader" 0x00040000-0x00240000 : "Kernel" 0x00240000-0x01240000 : "Filesystem" enable_irq(170) unbalanced from c0188f44 enable_irq(174) unbalanced from c0188f44 OHCI_PXA: starting PXA OHCI USB Controller Setting port 3 power failed. drivers/usb/host/ohci-pxa.c: ohci_hcd (PXA) at 0xf8000000, irq 3 pxa-ohci pxa-ohci: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usbcore: registered new driver cdc_acm drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver pxa27x_udc: version 23-Sep-2004 usb0: Ethernet Gadget, version: St Patrick's Day 2004 usb0: using pxa27x_udc, OUT Bulk-out-2 IN Bulk-in-1 usb0: MAC 3e:b6:bc:42:5f:74 mice: PS/2 mouse device common for all mice input: mainstoneIII keypad! platform bus: mainstoneIII keypad device! input: mainstoneIII keypad driver! enable_irq(18) unbalanced from c01acc88 I2C: Adding PXA i2c adapter. I2C: Scanning bus I2C: Successfully added bus I2C: PXA algorithm module loaded. ac97_codec: AC97 Audio codec, id: PSC4 (Philips UCB1400) IRQ9 (GPIO1): rising falling edges IRQ34 (GPIO2): rising falling edges IRQ35 (GPIO3): rising falling edges IRQ36 (GPIO4): rising falling edges IRQ37 (GPIO5): rising falling edges IRQ38 (GPIO6): rising falling edges IRQ39 (GPIO7): rising falling edges IRQ40 (GPIO8): rising falling edges IRQ41 (GPIO9): rising falling edges IRQ42 (GPIO10): rising falling edges IRQ44 (GPIO12): rising falling edges IRQ46 (GPIO14): rising falling edges IRQ49 (GPIO17): rising falling edges IRQ51 (GPIO19): rising falling edges IRQ54 (GPIO22): rising falling edges IRQ55 (GPIO23): rising falling edges IRQ56 (GPIO24): rising falling edges IRQ57 (GPIO25): rising falling edges IRQ58 (GPIO26): rising falling edges IRQ59 (GPIO27): rising falling edges IRQ64 (GPIO32): rising falling edges IRQ74 (GPIO42): rising falling edges IRQ75 (GPIO43): rising falling edges IRQ76 (GPIO44): rising falling edges IRQ78 (GPIO46): rising falling edges IRQ79 (GPIO47): rising falling edges IRQ85 (GPIO53): rising falling edges IRQ113 (GPIO81): rising falling edges IRQ114 (GPIO82): rising falling edges IRQ115 (GPIO83): rising falling edges IRQ116 (GPIO84): rising falling edges IRQ118 (GPIO86): rising falling edges IRQ119 (GPIO87): rising falling edges IRQ122 (GPIO90): rising falling edges IRQ123 (GPIO91): rising falling edges IRQ124 (GPIO92): rising falling edges IRQ127 (GPIO95): rising falling edges IRQ128 (GPIO96): rising falling edges IRQ141 (GPIO109): rising falling edges IRQ142 (GPIO110): rising falling edges IRQ143 (GPIO111): rising falling edges IRQ144 (GPIO112): rising falling edges IRQ146 (GPIO114): rising falling edges IRQ147 (GPIO115): rising falling edges IRQ148 (GPIO116): rising falling edges IRQ151 (GPIO119): rising falling edges IRQ152 (GPIO120): rising falling edges IRQ153 (GPIO121): rising falling edges IRQ154 (GPIO122): rising falling edges IRQ155 (GPIO123): rising falling edges IRQ156 (GPIO124): rising falling edges IRQ157 (GPIO125): rising falling edges IRQ158 (GPIO126): rising falling edges IRQ159 (GPIO127): rising falling edges enable_irq(164) unbalanced from c01b46f8 UCB1x00 Touchscreen Controller Driver. NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 8Kbytes TCP: Hash tables configured (established 8192 bind 16384) NET: Registered protocol family 1 min dma period: 880000 ps, new clock 624000 kHz min dma period: 880000 ps, new clock 624000 kHz eth0: link down IP-Config: Complete: device=eth0, addr=192.168.1.101, mask=255.255.255.0, gw=255.255.255.255, host=192.168.1.101, domain=, nis-domain=(none), bootserver=192.168.1.100, rootserver=192.168.1.100, rootpath= usb 1-1: new low speed USB device using address 2 input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-pxa27x-1 input: USB HID v1.10 Mouse [CHESEN USB Keyboard] on usb-pxa27x-1 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 VFS: Mounted root (jffs2 filesystem). Freeing init memory: 100K nfs warning: mount version newer than kernel NFS: mount program didn't pass remote address! nfs warning: mount version older than kernel nfs warning: mount version older than kernel nfs warning: mount version older than kernel