simestimII:/var/log# dmesg Linux version 2.6.22 (2.6.22-6) (root@simestimII) (gcc version 4.2.3 20071123 (prerelease) (Debian 4.2.2-4)) #2 SMP Wed Dec 5 19:56:45 CET 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009b800 (usable) BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007fed0000 (usable) BIOS-e820: 000000007fed0000 - 000000007fee1000 (ACPI NVS) BIOS-e820: 000000007fee1000 - 0000000080000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved) BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. found SMP MP-table at 000f7b80 Entering add_active_range(0, 0, 229376) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 early_node_map[1] active PFN ranges 0: 0 -> 229376 On node 0 totalpages: 229376 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 DMI present. ACPI: RSDP 000F7B50, 0024 (r2 PTLTD ) ACPI: XSDT 7FED387D, 007C (r1 ACRSYS ACRPRDCT 6040000 LTP 0) ACPI: FACP 7FEDDC2A, 00F4 (r3 INTEL CRESTLNE 6040000 ALAN 1) ACPI: DSDT 7FED4C20, 8F96 (r2 INTEL CRESTLNE 6040000 MSFT 3000001) ACPI: FACS 7FEE0FC0, 0040 ACPI: APIC 7FEDDD1E, 0068 (r1 INTEL CRESTLNE 6040000 LOHR 5A) ACPI: HPET 7FEDDD86, 0038 (r1 INTEL CRESTLNE 6040000 LOHR 5A) ACPI: MCFG 7FEDDDBE, 003C (r1 INTEL CRESTLNE 6040000 LOHR 5A) ACPI: APIC 7FEDDDFA, 0068 (r1 PTLTD APIC 6040000 LTP 0) ACPI: BOOT 7FEDDE62, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: SLIC 7FEDDE8A, 0176 (r1 ACRSYS ACRPRDCT 6040000 acer 0) ACPI: SSDT 7FED4943, 02DD (r1 SataRe SataAhci 1000 INTL 20050624) ACPI: SSDT 7FED3E85, 025F (r1 PmRef Cpu0Tst 3000 INTL 20050624) ACPI: SSDT 7FED3DDF, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20050624) ACPI: SSDT 7FED38F9, 04E6 (r1 PmRef CpuPm 3000 INTL 20050624) ACPI: BIOS bug: multiple APIC/MADT found, using 0 ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 6:15 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) Built 1 zonelists. Total pages: 227584 Kernel command line: root=/dev/sda3 ro vga=791 video=1280x800 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2000.184 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 900612k/917504k available (1693k kernel code, 16344k reserved, 655k data, 252k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffb6000 - 0xfffff000 ( 292 kB) vmalloc : 0xf8800000 - 0xfffb4000 ( 119 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0351000 - 0xc0390000 ( 252 kB) .data : 0xc02a76e7 - 0xc034b5bc ( 655 kB) .text : 0xc0100000 - 0xc02a76e7 (1693 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Calibrating delay using timer specific routine.. 4003.87 BogoMIPS (lpj=8007741) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20070126 CPU0: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4000.22 BogoMIPS (lpj=8000442) CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Core(TM)2 Duo CPU T7300 @ 2.00GHz stepping 0a Total of 2 processors activated (8004.09 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs migration_cost=25 Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources ACPI: System BIOS is requesting _OSI(Linux) ACPI: Please test with "acpi_osi=!Linux" Please send dmidecode to linux-acpi@vger.kernel.org ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *7 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 11 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0 PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.0 PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1 PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1 PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1 PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.3 PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.3 PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.3 PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.5 PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.5 PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.5 NET: Registered protocol family 8 NET: Registered protocol family 20 ACPI: RTC can wake from S4 pnp: 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved pnp: 00:04: iomem range 0xfed00000-0xfed003ff could not be reserved Time: tsc clocksource has been installed. Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 1 PCI: Failed to allocate mem resource #6:20000@e0000000 for 0000:01:00.0 PCI: Bridge: 0000:00:01.0 IO window: 2000-2fff MEM window: f0000000-f2ffffff PREFETCH window: d0000000-dfffffff PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.1 IO window: 3000-3fff MEM window: 88000000-880fffff PREFETCH window: 88100000-881fffff PCI: Bridge: 0000:00:1c.3 IO window: disabled. MEM window: 88200000-882fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.5 IO window: disabled. MEM window: 88300000-883fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: f3300000-f33fffff PREFETCH window: disabled. ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.0 to 64 PCI: Enabling device 0000:00:1c.1 (0000 -> 0003) ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.1 to 64 PCI: Enabling device 0000:00:1c.3 (0000 -> 0002) ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.3 to 64 PCI: Enabling device 0000:00:1c.5 (0000 -> 0002) ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1c.5 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 5367k freed Simple Boot Flag at 0x35 set to 0x1 audit: initializing netlink socket (disabled) audit(1196912150.612:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie02] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] PCI: Setting latency timer of device 0000:00:1c.3 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.3:pcie00] Allocate Port Service[0000:00:1c.3:pcie02] Allocate Port Service[0000:00:1c.3:pcie03] PCI: Setting latency timer of device 0000:00:1c.5 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.5:pcie00] Allocate Port Service[0000:00:1c.5:pcie02] Allocate Port Service[0000:00:1c.5:pcie03] vesafb: framebuffer at 0xf1000000, mapped to 0xf8880000, using 3072k, total 14336k vesafb: mode is 1024x768x16, linelength=2048, pages=1 vesafb: protected mode interface info at c000:b310 vesafb: pmi: set display start = c00cb373, set palette = c00cb3ce vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found hpet_resources: 0xfed00000 is busy Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode Freeing unused kernel memory: 252k freed input: AT Translated Set 2 keyboard as /class/input/input0 ACPI: SSDT 7FED4601, 027A (r1 PmRef Cpu0Ist 3000 INTL 20050624) ACPI: SSDT 7FED40E4, 0498 (r1 PmRef Cpu0Cst 3001 INTL 20050624) Monitor-Mwait will be used to enter C-1 state Monitor-Mwait will be used to enter C-2 state Monitor-Mwait will be used to enter C-3 state ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: SSDT 7FED487B, 00C8 (r1 PmRef Cpu1Ist 3000 INTL 20050624) ACPI: SSDT 7FED457C, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050624) ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU1] (supports 8 throttling states) Marking TSC unstable due to: possible TSC halt in C2. Time: hpet clocksource has been installed. ACPI: Thermal Zone [THRM] (53 C) usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb USB Universal Host Controller Interface driver v3.0 SCSI subsystem initialized libata version 2.21 loaded. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx tg3.c:v3.77 (May 31, 2007) PCI: Enabling device 0000:08:00.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:08:00.0 to 64 eth0: Tigon3 [partno(BCM95787m) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:1b:24:57:94:25 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller udev: renamed network interface eth0 to eth1 uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Clocksource tsc unstable (delta = -127835049 ns) ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1a.1: irq 19, io base 0x00001820 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001840 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usb 1-2: new full speed USB device using uhci_hcd and address 2 ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.1: irq 18, io base 0x00001860 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 1-2: configuration #1 chosen from 1 choice ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 21, io mem 0xf3604800 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 4 ports detected usb 1-2: can't set config #1, error -71 usb 1-2: USB disconnect, address 2 ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 6 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xf3604c00 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 6 ports detected ahci 0000:00:1f.2: version 2.2 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 18 ahci 0000:00:1f.2: nr_ports (3) and implemented port map (0x1) don't match usb 5-2: new high speed USB device using ehci_hcd and address 2 usb 5-2: configuration #1 chosen from 1 choice usb 4-2: new low speed USB device using uhci_hcd and address 2 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x1 impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci ata1: SATA max UDMA/133 cmd 0xf8bb6100 ctl 0x00000000 bmdma 0x00000000 irq 218 usb 4-2: configuration #1 chosen from 1 choice ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: Hitachi HTS541616J9SA00, SB4OC70P, max UDMA/100 ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (not used) ata1.00: configured for UDMA/100 scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54161 SB4O PQ: 0 ANSI: 5 ACPI: PCI Interrupt 0000:0a:09.0[A] -> <6>ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001880 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected GSI 16 (level, low) -> IRQ 16 sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda:<5>firewire_ohci: Added fw-ohci device 0000:0a:09.0, OHCI version 1.10 ICH8M: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 19 (level, low) -> IRQ 18 ICH8M: chipset revision 3 ICH8M: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x18a0-0x18a7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x18a8-0x18af, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... usbcore: registered new interface driver hiddev input: Microsoft Microsoft(R) Compact Optical Mouse as /class/input/input1 input: USB HID v1.10 Mouse [Microsoft Microsoft(R) Compact Optical Mouse] on usb-0000:00:1d.1-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk firewire_core: created new fw device fw0 (0 config rom retries) hda: Slimtype DVD A DS8A1P, ATAPI CD/DVD-ROM drive hda: selected mode 0x42 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ReiserFS: sda3: found reiserfs format "3.6" with standard journal ReiserFS: sda3: using ordered data mode ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda3: checking transaction log (sda3) ReiserFS: sda3: Using r5 hash to sort names Linux agpgart interface v0.102 (c) Dave Jones sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci: SDHCI controller found at 0000:0a:09.1 [1180:0822] (rev 22) ACPI: PCI Interrupt 0000:0a:09.1[B] -> GSI 17 (level, low) -> IRQ 17 mmc0: SDHCI at 0xf3300800 irq 17 DMA Real Time Clock Driver v1.12ac ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 19 (level, low) -> IRQ 18 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:00:1b.0 to 64 Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1e0b1, caps: 0xc04751/0xe0500f input: SynPS/2 Synaptics TouchPad as /class/input/input2 Synaptics Touchpad, model: 1, fw: 6.5, id: 0x81a0b1, caps: 0xa04711/0xa04000 input: SynPS/2 Synaptics TouchPad as /class/input/input3 loop: module loaded device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com fuse init (API version 7.8) NET: Registered protocol family 10 lo: Disabled Privacy Extensions ACPI: Battery Slot [BAT1] (battery absent) ACPI: AC Adapter [ACAD] (on-line) input: Power Button (FF) as /class/input/input4 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /class/input/input5 ACPI: Lid Switch [LID] input: Power Button (CM) as /class/input/input6 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input7 ACPI: Sleep Button (CM) [SLPB] nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007 atkbd.c: Unknown key pressed (translated set 2, code 0xf2 on isa0060/serio0). atkbd.c: Use 'setkeycodes e072 ' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xf2 on isa0060/serio0). atkbd.c: Use 'setkeycodes e072 ' to make it known.