AVM_Ar7 >AVM decompress Kernel: ............done start kernel [ohio_pre_init] System Clk = 62500000 Hz LINUX started... Linux version 2.6.13.1-ohio (1320) (gcc version 3.4.6) #1 Wed Dec 12 15:47:14 C7 memsize=32 MByte flashsize=8 MByte &_end=0x94239fe8 PFN_ALIGN(&_end)=0x9423a000 CPHYSADDR(PFN_ALIGN(&_end))=0x14230 CPU revision is: 00018448 [ohio_gpio_init] Determined physical RAM map: memory: 0023a000 @ 14000000 (reserved) memory: 01dc6000 @ 1423a000 (usable) On node 0 totalpages: 8192 [alloc_node_mem_map] reduce size from 2883616 Bytes to 262176 Bytes [alloc_node_mem_map]: (org) sizeof(mem_map) = 262176 mem_map=0x9423d000-0x9427d0 [alloc_node_mem_map]: sizeof(mem_map) = 2883616 mem_map=0x93fbd000-0x9427d020 zone=0 zone_size[j]=0x90112 realsize=8192 DMA zone: 8192 pages, LIFO batch:3 zone=1 zone_size[j]=0x0 realsize=0 Normal zone: 0 pages, LIFO batch:1 zone=2 zone_size[j]=0x0 realsize=0 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: idle=4 console=ttyS0,38400n8r [ld_mmu_r4xx0] memcpy((void *)(CAC_BASE + 0x100), &except_vec2_generic, 0x30) Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes. Primary data cache 8kB, 4-way, linesize 16 bytes. Synthesized TLB refill handler (20 instructions). Base=0x942017cc TLB synthesizer field overflow (simm) Synthesized TLB load handler fastpath (34 instructions) Base=0x94204620. TLB synthesizer field overflow (simm) Synthesized TLB store handler fastpath (34 instructions) Base=0x94204820. TLB synthesizer field overflow (simm) Synthesized TLB modify handler fastpath (33 instructions) Base=0x94204a20. PID hash table entries: 256 (order: 8, 4096 bytes) CPU frequency 211.97 MHz Using 105.984 MHz high precision timer. [setup_irq]: irq 255 irqaction->handler 0x940428c0 (no_action+0x0/0x8 ) [register_console] enable commandline console 0 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 30104k/30488k available (1562k kernel code, 320k reserved, 382k data, 1) totalram_pages= 7542 Calibrating delay loop... 211.35 BogoMIPS (lpj=1056768) loops_per_jiffy=1056768 Mount-cache hash table entries: 512 Checking for 'wait' instruction... [speedup] idle_mode = 4 with idle values available. NET: Registered protocol family 16 Can't analyze prologue code at 94184f54 Squashfs 2.2-r2b (released 2006/02/23) (C) 2002-2005 Phillip Lougher avm_net_trace: Up and running. [avm_power]Ohio250 detected -> overclocking possible [avm] configured: watchdog eventled enable shift register enable direct gpio gpio usage: reset=12 clock=13 store=10 data=9 AR7WDT: Watchdog Driver for AR7 Hardware (Version 1.0, build: Dec 12 2007 15:44) Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled [uart_add_one_port] ttyS0 at MMIO 0x0 (irq = 15) is a OHIO_UART [uart_add_one_port] dont register console port->type = 16 port->cons = 0x941c5f50 port->cons->flags = 0x7 [uart_add_one_port] success io scheduler noop registered [cpmac] [cpmac_if_register] dev cpmac0 (phy_id 0) registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky physmap flash device: 400000 at 10000000 phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 phys_mapped_flash: Swapping erase regions for broken CFI table. number of CFI chips: 1 RedBoot partition parsing not available Generic platform RAM MTD, (c) 2004 Simtec Electronics Ohio flash driver (size->0x400000 mem->0x10000000) flash_size=0x800000 flash_mask=0xffffff Ohio flash memory: Found 1 x16 devices at 0x0 in 16-bit bank [genprobe_ident_chips] 4 i 0 j 0 [genprobe_ident_chips] 5 i 0 j 1 Amd/Fujitsu Extended Query Table at 0x0040 Ohio flash memory: Swapping erase regions for broken CFI table. number of CFI chips: 1 [mtd]: jffs2_size = 7 * 64KByte (0x70000 Bytes) [ohio_find_hidden_filesystem]: super block found: bytes_used: 0x68e8c2/6875330 [init_ohio_flash] find hidden filesystem size=0x6cab00 offset=0xb5500 [mtd] configure jffs2 partition [mtd] fs_size=0x740000 max=0x30000 is=0x70000 max jffs2_size value 3 [mtd] ERROR jffs2_size too big, reduce to max [mtd] ohio_flash_map: name=Ohio flash memory bankwidth=2 virt=0xb0000000 phys=00 Creating 7 MTD partitions on "Ohio flash memory": 0x000b5500-0x00780000 : "filesystem" 'nor-flash' 'Bits can be cleared (flash)' 'Has an erase function' mtd: partition "filesystem" doesn't start on an erase block boundary -- force ry 0x00010000-0x00780000 : "kernel" 'nor-flash' 'Bits can be cleared (flash)' 'Has an erase function' 0x00000000-0x00010000 : "bootloader" 'nor-flash' 'Bits can be cleared (flash)' 'Has an erase function' 0x00780000-0x007c0000 : "tffs (1)" 'nor-flash' 'Bits can be cleared (flash)' 'Has an erase function' 0x007c0000-0x00800000 : "tffs (2)" 'nor-flash' 'Bits can be cleared (flash)' 'Has an erase function' 0x00750000-0x00780000 : "jffs2" 'nor-flash' 'Bits can be cleared (flash)' 'Has an erase function' 0x00010000-0x00750000 : "Kernel without jffs2" 'nor-flash' 'Bits can be cleared (flash)' 'Has an erase function' partition_info[0]: name=filesystem offset=b5500 size=6cab00 partition_info[0]: 0xb00b5500: 0x73717368 0x8b0 partition_info[1]: name=kernel offset=10000 size=770000 partition_info[1]: 0xb0010000: 0xfeed1281 0xa53e8 partition_info[2]: name=bootloader offset=0 size=10000 partition_info[2]: 0xb0000000: 0x40809000 0x40809800 partition_info[3]: name=tffs (1) offset=780000 size=40000 partition_info[3]: 0xb0780000: 0x40001 0xd7ffffff partition_info[4]: name=tffs (2) offset=7c0000 size=40000 partition_info[4]: 0xb07c0000: 0x40001 0xd6ffffff partition_info[5]: name=jffs2 offset=750000 size=30000 partition_info[5]: 0xb0750000: 0x20031985 0xc partition_info[6]: name=Kernel without jffs2 offset=10000 size=740000 partition_info[6]: 0xb0010000: 0xfeed1281 0xa53e8 NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered TCP bic registered mcfw: IGMPv3 fast forwarding NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 [setup_irq]: irq 1 irqaction->handler 0x94001590 (dummy_timer_irq+0x0/0x14 ) [setup_irq]: irq 6 irqaction->handler 0x940015a4 (dummy_system_irq_2+0x0/0x14 ) [ohio_late_init] [avm_new] push_button_gpio=8 value=1 enabled TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0) mount on mtd4 and mtd5 (double buffering) Adam2 environment variables API installed. [prepare_namespace] new mount root /dev/mtdblock1 use lzma compression VFS: Mounted root (squashfs filesystem) readonly. Freeing prom memory: 0kb freed Freeing unused kernel memory: 112k freed (7570 free) [setup_irq]: irq 15 irqaction->handler 0x940d9b8c (serial8250_interrupt+0x0/0x1) init started: BusyBox v1.8.2 (2007-12-09 19:36:38 CET) rootdir=/ table='/etc/device.table' AR7WDT: System Init UEberwachung 240 Sekunden TFFS Name Table D HWRevision 102.1.1.0 ProductID Fritz_Box_DECT_W900V SerialNumber 0000000000000000 annex B autoload yes bootloaderVersion 1.153 bluetooth 00:04:0E:FF:FF:07 cpufrequency 211968000 firstfreeaddress 0x946AE570 firmware_version avm firmware_info 29.04.48 flashsize 0x00800000 jffs2_size 7 kernel_args idle=4 maca 00:04:0E:DE:9F:46 macb 00:04:0E:DE:9F:47 macwlan 00:04:0E:DE:9F:48 macdsl 00:04:0E:DE:9F:49 memsize 0x02000000 modetty0 38400,n,8,1,hw modetty1 38400,n,8,1,hw mtd0 0x90000000,0x90000000 mtd1 0x90010000,0x90780000 mtd2 0x90000000,0x90010000 mtd3 0x90780000,0x907C0000 mtd4 0x907C0000,0x90800000 mtd5 0x90780000,0x90780000 my_ipaddress 192.168.178.1 prompt AVM_Ar7 ptest reserved 00:04:0E:FF:FF:00 req_fullrate_freq 125000000 sysfrequency 125000000 urlader-version 1153 usb_board_mac 00:04:0E:DE:9F:4A usb_rndis_mac 00:04:0E:DE:9F:4B usb_device_id 0x0000 usb_revision_id 0x0000 usb_device_name USB DSL Device usb_manufacturer_name AVM wlan_key 2881006638504243 wlan_cal 0013,03F8,0014,00F4,010A,0105,010A,0302,0353 mknod: /var/flash/ar7.cfg: File exists Loading /var/flash/ds_mod...done. Loading users, groups and passwords...done. Loading hosts...done. Loading config...[avm_new]push_button 'Wlan-Taster', released: GPIO=8 presses=93 done. Loading modules...done. cp /etc/default.049/fx_moh.default /var/fx_moh Piglet: module license ' (C) Copyright 2005 by AVM ' taints kernel. EMIF: asize=1 ta=3 r_hold=0 w_strobe=6 r_strobe=6 ew=1 [avm_new]push_button_ctrl:'ATA-Schalter': enable=1 gpio=0 regaddr=be00002c butt2 [jffs2] xx=mtd6: 00030000 00010000 "jffs2" [jffs2] i=mtd6: [jffs2] jffs2_pat=6 [jffs2] i=00030000 [jffs2] jffs2_size=3 [jffs2] i=0001000[avm_new]push_button 'ATA-Schalter', released: GPIO=0 presses=8 0 [jffs2] i="jffs2" [jffs2] load jffs2 module JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. [jffs2] mount jffs jffs2: Too few erase blocks (3) mount: mounting /dev/mtdblock6 on /data failed: Invalid argument copying image... done. jffs2: Too few erase blocks (3) mount: mounting /dev/mtdblock6 on /data failed: Invalid argument TAM: create JFFS2 directory /data/tam mkdir: cannot create directory '/data/tam': Read-only file system TAM Defaults: User Directory /data/tam not found! attempting to load DSL Firmware '/lib/modules/microvoip-dsl.bin' **** ANNEX: 'B' ************************************* setting DSL Firmware to Annex B registered device TI Avalanche SAR tiatm driver (patch_annex=0xc00e032c) [tiatm] Set StrictPriority=0 DSP binary filesize = 303784 bytes [tiatm] INFO V2U-BRIDGEREGISTER: 0x00000019 [avm_power]Ohio250 detected -> overclocking possible [avm_power]#### boostVoltage: DSP Core voltage set to 1,5 V #### [setup_irq]: irq 23 irqaction->handler 0xc00c7208 (tn7atm_sar_irq+0x0/0x30 [tia) [setup_irq]: irq 31 irqaction->handler 0xc00c7238 (tn7atm_dsl_irq+0x0/0x28 [tia) [tiatm]: Powermanagment (States => 1,3,10) supported! Texas Instruments ATM driver: version:[4.07.06.00] [tiatm] AvmInterface length: 40 ubik2 driver (ubik2 - 0x10=0xc003b8f4) atm_dsp_register_ubik2: ubik2_ToMIPS_notify=0xc002abfc atm_dsp_register_ubik2: dsp mem pointer 0xa1c0f218 ubik2_init_interface: DSP-Link Version v3 8480 checkempty: : No such file or directory driver params overwritten io_addr=0x0 irq_num=0 [4294939438][isdn]svn:2146 gpio_ssi_init: done [setup_irq]: irq 28 irqaction->handler 0xc00354a0 (soft_interrupt_handler+0x0/0) [4294939443]CPU-Clk: 105 * 2 MHz [4294939443]DSP-Fw: Version 3.183] EC=3 DTMF=3 Slots=10 BChan=8(Analog=4) DChan [4294939496]BLK: DECT-Hardware detected! [4294939496]BLK: DECT StartUp, mode = WAIT, firmware: 00.31.12 [4294939557]BLK: DECT StartUp, mode = MASTER INIT, firmware: 00.31.12 capicodec_init() [capi_codec] support fax [capi_codec] support Codecs usbcore: registered new driver usbfs usbcore: registered new driver hub AHCI RevisionID = 0x02, RamSize = 16384, NumPorts= 1 [setup_irq]: irq 9 irqaction->handler 0xc00bd490 (ahci_irq+0x0/0x880 [usbahcico) ahci : new USB bus registered, assigned bus number 1 AVM USB 1.1 Host started /etc/init.d/rc.S: line 1016: +case: not found /etc/init.d/rc.S: line 1017: syntax error: ")" unexpected Please press Enter to activate this console. hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected [4294940450]DSP: XDU=3( ) OVR=0 MIPS_OVR=4 BusyBox v1.8.2 (2007-12-09 19:36:38 CET) built-in shell (ash) Enter 'help' for a list of built-in commands.