Linux version 2.6.23-gentoo-r4 (root@Cherry) (gcc version 4.2.2 (Gentoo 4.2.2 p1.0)) #5 SMP Fri Dec 21 22:43:02 ART 2007
Command line: root=/dev/sda6 X_DRIVER=radeon splash=silent vga=0x0317 video=vesafb:ywrap,mtrr:3
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ffd0000 (usable)
 BIOS-e820: 000000007ffd0000 - 000000007ffde000 (ACPI data)
 BIOS-e820: 000000007ffde000 - 0000000080000000 (ACPI NVS)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524240) 1 entries of 256 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F9A50, 0014 (r0 ACPIAM)
ACPI: RSDT 7FFD0000, 0038 (r1 090307 RSDT1050 20070903 MSFT       97)
ACPI: FACP 7FFD0200, 0084 (r2 090307 FACP1050 20070903 MSFT       97)
ACPI: DSDT 7FFD0430, 4271 (r1  1ADNC 1ADNCB33      B33 INTL 20051117)
ACPI: FACS 7FFDE000, 0040
ACPI: APIC 7FFD0390, 005C (r1 090307 APIC1050 20070903 MSFT       97)
ACPI: MCFG 7FFD03F0, 003C (r1 090307 OEMMCFG  20070903 MSFT       97)
ACPI: OEMB 7FFDE040, 0071 (r1 090307 OEMB1050 20070903 MSFT       97)
ACPI: HPET 7FFD46B0, 0038 (r1 090307 OEMHPET  20070903 MSFT       97)
Entering add_active_range(0, 0, 159) 0 entries of 256 used
Entering add_active_range(0, 256, 524240) 1 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      159
    0:      256 ->   524240
On node 0 totalpages: 524143
  DMA zone: 56 pages used for memmap
  DMA zone: 803 pages reserved
  DMA zone: 3140 pages, LIFO batch:0
  DMA32 zone: 7111 pages used for memmap
  DMA32 zone: 513033 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8300 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ff00000)
PERCPU: Allocating 33064 bytes of per cpu data
Built 1 zonelists in Zone order.  Total pages: 516173
Kernel command line: root=/dev/sda6 X_DRIVER=radeon splash=silent vga=0x0317 video=vesafb:ywrap,mtrr:3
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2294.504 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 2061296k/2096960k available (1883k kernel code, 35124k reserved, 610k data, 200k init)
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
Calibrating delay using timer specific routine.. 4701.10 BogoMIPS (lpj=7832173)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Freeing SMP alternatives: 22k freed
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12470142
Detected 12.470 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4590.24 BogoMIPS (lpj=7648391)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4400+ stepping 01
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] -  74, should be 72 [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnpacpi: exceeded the max number of IO resources: 24
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 32-bit timers, 14318180 Hz
Time: hpet clocksource has been installed.
pnp: 00:07: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:07: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:08: ioport range 0x40b-0x40b has been reserved
pnp: 00:08: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:08: ioport range 0xc00-0xc01 has been reserved
pnp: 00:08: ioport range 0xc14-0xc14 has been reserved
pnp: 00:08: ioport range 0xc50-0xc51 has been reserved
pnp: 00:08: ioport range 0xc52-0xc52 has been reserved
pnp: 00:08: ioport range 0xc6c-0xc6c has been reserved
pnp: 00:08: ioport range 0xc6f-0xc6f has been reserved
pnp: 00:08: ioport range 0xcd0-0xcd1 has been reserved
pnp: 00:08: ioport range 0xcd2-0xcd3 has been reserved
pnp: 00:08: iomem range 0xffb80000-0xffbfffff has been reserved
pnp: 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:0a: ioport range 0x600-0x6df has been reserved
pnp: 00:0a: ioport range 0xae0-0xaef has been reserved
pnp: 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0c: iomem range 0xc0000-0xcffff has been reserved
pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0c: iomem range 0x100000-0x7fffffff could not be reserved
pnp: 00:0c: iomem range 0xfec00000-0xffffffff could not be reserved
PCI: Bridge: 0000:00:02.0
  IO window: c000-cfff
  MEM window: fe900000-fe9fffff
  PREFETCH window: d0000000-dfffffff
PCI: Bridge: 0000:00:07.0
  IO window: d000-dfff
  MEM window: fea00000-feafffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:14.4
  IO window: e000-efff
  MEM window: feb00000-febfffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Total HugeTLB memory allocated, 0
io scheduler noop registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
hpet_resources: 0xfed00000 is busy
vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20000080000, using 3072k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
input: Power Button (FF) as /devices/virtual/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: duty_cycle spans bit 4
loop: module loaded
ahci 0000:00:12.0: version 2.3
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20000020900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata2: SATA max UDMA/133 cmd 0xffffc20000020980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata3: SATA max UDMA/133 cmd 0xffffc20000020a00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata4: SATA max UDMA/133 cmd 0xffffc20000020a80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: WDC WD1600AABS-00PRA0, 05.06H05, max UDMA/133
ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      WDC WD1600AABS-0 05.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors (160042 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
usbmon: debugfs is not available
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
ReiserFS: sda6: found reiserfs format "3.6" with standard journal
ReiserFS: sda6: using ordered data mode
ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda6: checking transaction log (sda6)
ReiserFS: sda6: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 200k freed
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: RTL8168b/8111b at 0xffffc20000050000, 00:19:db:d2:c6:74, XID 38000000 IRQ 19
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe8ff000
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe8fe000
Linux video capture interface: v2.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe8fd000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe8fc000
saa7130/34: v4l2 driver version 0.2.14 loaded
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-8: new high speed USB device using ehci_hcd and address 3
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
SB600_PATA: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:03:03.0[A] -> <6>ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
GSI 21 (level, low) -> IRQ 21
saa7130[0]: found at 0000:03:03.0, rev: 1, irq: 21, latency: 64, mmio: 0xfebffc00
SB600_PATA: chipset revision 0
SB600_PATA: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xff00-0xff07<6>saa7130[0]: subsystem: 1131:2341, board: Encore ENLTV [card=106,autodetected]
, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
saa7130[0]: board init: gpio is 5d31ff
input: saa7134 IR (Encore ENLTV) as /devices/pci0000:00/0000:00:14.4/0000:03:03.0/input/input3
usb 1-8: configuration #1 chosen from 1 choice
saa7130[0]: i2c eeprom 00: 31 11 41 23 08 20 1c 55 43 43 a9 1c 55 43 43 a9
saa7130[0]: i2c eeprom 10: ff ff 00 00 31 30 4d 4f 4f 4e 53 37 31 33 30 20
saa7130[0]: i2c eeprom 20: 41 41 48 53 ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
Initializing USB Mass Storage driver...
tuner 1-0060: All bytes are equal. It is not a TEA5767
tuner 1-0060: chip found @ 0xc0 (saa7130[0])
tuner 1-0060: type set to 69 (Tena TNF 5335 and similar models)
tuner 1-0060: type set to 69 (Tena TNF 5335 and similar models)
tuner 1-0061: chip found @ 0xc2 (saa7130[0])
saa7130[0]: registered device video0 [v4l2]
saa7130[0]: registered device vbi0
saa7130[0]: registered device radio0
usb 2-1: new low speed USB device using ohci_hcd and address 2
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 1886 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.44.3 [Dec 19 2007] on minor 0
usb 2-1: configuration #1 chosen from 1 choice
input: USB Mouse as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1:1.0/input/input4
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:13.0-1
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
hda: HL-DT-ST DVDRAM GSA-H42N, ATAPI CD/DVD-ROM drive
hda: selected mode 0x44
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 22
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe8fb000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe8fa000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ReiserFS: sda6: switching to writeback data mode
fuse init (API version 7.8)
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access     Multi    Flash Reader     1.00 PQ: 0 ANSI: 0
sd 4:0:0:0: [sdb] Attached SCSI removable disk
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: Using r5 hash to sort names
SGI XFS with large block/inode numbers, no debug enabled
XFS mounting filesystem sda2
Ending clean XFS mount for filesystem: sda2
Adding 787144k swap on /dev/sda7.  Priority:-1 extents:1 across:787144k
r8169: eth0: link up
r8169: eth0: link up
[fglrx] Disable PAT
[fglrx] asyncIODestroy finished!
[fglrx] module unloaded - fglrx 8.44.3 [Dec 19 2007] on minor 0
[drm] Initialized drm 1.1.0 20060810
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period