; An implementation of Skinny Client Control Protocol (SCCP) ; ; Sergio Chersovani (mlists@c-net.it) ; http://chan-sccp.belios.de ; [general] servername = Asterisk-PBX ; show this name on the device registration keepalive = 60 ; phone keep alive message evey 60 secs. Used to check the voicemail debug = 5 ; console debug level. 1 => 10 context = from-internal dateFormat = D.M.Y ; M-D-Y in any order. Use M/D/YA (for 12h format) bindaddr = 192.168.1.4 ; replace with the ip address of the asterisk server (RTP important param) port = 2000 ; listen on port 2000 (Skinny, default) disallow=all ; First disallow all codecs allow=g729 allow=alaw ; Allow codecs in order of preference allow=ulaw ; firstdigittimeout = 16 ; dialing timeout for the 1st digit digittimeout = 8 ; more digits digittimeoutchar = # ; you can force the channel to dial with this char in the dialing state autoanswer_ring_time = 0 ; ringing time in seconds for the autoanswer, the default is 0 ;autoanswer_tone = 0x32 ; autoanswer confirmation tone. For a complete list of tones: grep SKINNY_TONE sccp_protocol.h ; not all the tones can be played in a connected state, so you have to try. ;remotehangup_tone = 0x32 ; passive hangup notification. 0 for none ;transfer_tone = 0 ; confirmation tone on transfer. Works only between SCCP devices ;callwaiting_tone = 0x2d ; sets to 0 to disable the callwaiting tone ;musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=skinny ; accountcode to ease billing ;deny=0.0.0.0/0.0.0.0 ; Deny every address except for the only one allowed. ;permit=192.168.1.0/255.255.255.0 ; Accept class C 192.168.1.0 ; You may have multiple rules for masking traffic. ; Rules are processed from the first to the last. ; This General rule is valid for all incoming connections. It's the 1st filter. localnet = 192.168.1.0/255.255.255.0 ; All RFC 1918 addresses are local networks ;externip = 1.2.3.4 ; IP Address that we're going to notify in RTP media stream ;externhost = mydomain.dyndns.org ; Hostname (if dynamic) that we're going to notify in RTP media stream ;externrefresh = 60 ; expire time in seconds for the hostname (dns resolution) ;dnd = on ; turn on the dnd softkey for all devices. Valid values are "off", "on" (busy signal), "reject" (busy signal), "silent" (ringer = silent) ;rtptos = 184 ; sets the default rtp packets TOS ;echocancel = on ; sets the phone echocancel for all devices ;silencesuppression = off ; sets the silence suppression for all devices ;callgroup=1 ; We are in caller groups 1,3,4. Valid for all lines ;pickupgroup=1 ; We can do call pick-p for call group 1,3,4,5. Valid for all lines ;amaflags = ; Sets the default AMA flag code stored in the CDR record ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;tos = 0x68 ; call control packets tos (0x68 Assured forwarding) ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. ;private = on ; permit the private function softkey ;mwilamp = wink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink ;mwioncall = on ; Set the MWI on call. blindtransferindication = ring ; moh or ring. the blind transfer should ring the caller or just play music on ; hold ;protocolversion = 3 ; skinny version protocol. Just for testing. 2 to 6 ;cfwdall = off ; activate the callforward ALL stuff and softkeys ;cfwdbusy = off ; activate the callforward BUSY stuff and softkeys [devices] type = 7970 ; device type (see below) autologin = 130,131,132,133 ; lines list. You can add an empty line for an empty button (7960, 7970, 7940, 7920) description = Phone7970 ; internal description. Not important keepalive = 60 ; set 0 to disable the keepalive check. tzoffset = -1 transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey park = on ; take a look to the compile howto. Park stuff is not compiled by default speeddial = 101,Living Room,1234 speeddial = 102,Leannes,1244 speeddial = 200,M5235,1254 ; you can add an empty speedial if you want an empty button (7960, 7970, 7920) ;speeddial = 123,Jeff Conf ; speeddial number and name ;speeddial = 129,Greg SoftPhone cfwdall = on ; activate the callforward stuff and softkeys cfwdbusy = on dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play. ; Some phone model does not play dtmf tones while connected (bug?), so the default is inband ;imageversion = P00405000700 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server) ;deny=0.0.0.0/0.0.0.0 ; Same as general ;permit=192.168.1.45/255.255.255.255 ; This device can register only using this ip address dnd = on ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy ; signal), "reject" (busy signal), "silent" (ringer = silent) ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. private = on ; permit the private function softkey for this device mwilamp = blink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink mwioncall = on ; Set the MWI on call. device => SEP0012BLAHBLAH ; device name SEP type = 7970 ; device type (see below) autologin = 135 ; lines list. You can add an empty line for an empty button (7960, 7970, 7940, 7920) description = IP Communicator ; internal description. Not important keepalive = 60 ; set 0 to disable the keepalive check. tzoffset = -1 transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey park = on ; take a look to the compile howto. Park stuff is not compiled by default ;speeddial = 135,Ext 135,1214 ; you can add an empty speedial if you want an empty button (7960, 7970, 7920) speeddial = 123,Jeff Conf ; speeddial number and name speeddial = 131,Other Cisco cfwdall = on ; activate the callforward stuff and softkeys cfwdbusy = on dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play. ; Some phone model does not play dtmf tones while connected (bug?), so the default is inband ;imageversion = P00405000700 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp ;server) ;deny=0.0.0.0/0.0.0.0 ; Same as general ;permit=192.168.1.45/255.255.255.255 ; This device can register only using this ip address dnd = on ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy ; signal), "reject" (busy signal), "silent" (ringer = silent) ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. private = on ; permit the private function softkey for this device mwilamp = blink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink mwioncall = on ; Set the MWI on call. device => SEP00BLAHBLAHF0 ; device name SEP type = 7912 autologin = 136 description = 7912 keepalive = 60 ;tzoffset = +1 transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey park = on ; take a look to the compile howto. Park stuff is not compiled by default ;speeddial = ;speeddial = ;speeddial = 133,Ext 133,1224 ; you can add an empty speedial if you want an empty button (7960, 7970, 7920) speeddial = 123,Jeff Conf ; speeddial number and name ;speeddial = 129,Greg SoftPhone cfwdall = on ; activate the callforward stuff and softkeys cfwdbusy = on dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play. ; Some phone model does not play dtmf tones while connected (bug?), so the default is inband ;imageversion = P00405000700 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server) ;deny=0.0.0.0/0.0.0.0 ; Same as general ;permit=192.168.1.45/255.255.255.255 ; This device can register only using this ip address dnd = on ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy ; signal), "reject" (busy signal), "silent" (ringer = silent) ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. private = off ; permit the private function softkey for this device mwilamp = blink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink mwioncall = on ; Set the MWI on call. device => SEP0015F97F45E7 ; device name SEP type = ata autologin = 137 description = ATA1-186-Line1 keepalive = 60 ;tzoffset = +1 transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey park = on ; take a look to the compile howto. Park stuff is not compiled by default ;speeddial = ;speeddial = cfwdall = on ; activate the callforward stuff and softkeys cfwdbusy = on dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play. ; Some phone model does not play dtmf tones while connected (bug?), so the default is inband ;imageversion = P00405000700 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server) ;deny=0.0.0.0/0.0.0.0 ; Same as general ;permit=192.168.1.45/255.255.255.255 ; This device can register only using this ip address dnd = off ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy ; signal), "reject" (busy signal), "silent" (ringer = silent) ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. private = off ; permit the private function softkey for this device mwilamp = blink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink mwioncall = on ; Set the MWI on call. device => ATA001193CEFE7D ; device name SEP type = ata autologin = 138 description = ATA1-186-Line2 keepalive = 60 ;tzoffset = +1 transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey park = on ; take a look to the compile howto. Park stuff is not compiled by default ;speeddial = ;speeddial = cfwdall = on ; activate the callforward stuff and softkeys cfwdbusy = on dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play. ; Some phone model does not play dtmf tones while connected (bug?), so the default is inband ;imageversion = P00405000700 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server) ;deny=0.0.0.0/0.0.0.0 ; Same as general ;permit=192.168.1.45/255.255.255.255 ; This device can register only using this ip address dnd = off ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy ; signal), "reject" (busy signal), "silent" (ringer = silent) ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. private = off ; permit the private function softkey for this device mwilamp = blink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink mwioncall = on ; Set the MWI on call. device => ATA1193CEFE7D01 ; device name SEP type = ata autologin = 101 description = ATA2-186-Line1 keepalive = 60 ;tzoffset = +1 transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey park = on ; take a look to the compile howto. Park stuff is not compiled by default ;speeddial = ;speeddial = cfwdall = on ; activate the callforward stuff and softkeys cfwdbusy = on dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play. ; Some phone model does not play dtmf tones while connected (bug?), so the default is inband ;imageversion = P00405000700 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server) ;deny=0.0.0.0/0.0.0.0 ; Same as general ;permit=192.168.1.45/255.255.255.255 ; This device can register only using this ip address dnd = off ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy ; signal), "reject" (busy signal), "silent" (ringer = silent) ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. private = off ; permit the private function softkey for this device mwilamp = blink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink mwioncall = on ; Set the MWI on call. device => ATA0013C4297AF1 ; device name SEP type = ata autologin = 140 description = ATA2-186-Line2 keepalive = 60 ;tzoffset = +1 transfer = on ; enable or disable the transfer capability. It does remove the transfer softkey park = on ; take a look to the compile howto. Park stuff is not compiled by default ;speeddial = ;speeddial = cfwdall = on ; activate the callforward stuff and softkeys cfwdbusy = on dtmfmode = inband ; inband or outofband. outofband is the native cisco dtmf tone play. ; Some phone model does not play dtmf tones while connected (bug?), so the default is inband ;imageversion = P00405000700 ; useful to upgrade old firmwares (the ones that do not load *.xml from the tftp server) ;deny=0.0.0.0/0.0.0.0 ; Same as general ;permit=192.168.1.45/255.255.255.255 ; This device can register only using this ip address dnd = off ; turn on the dnd softkey for this device. Valid values are "off", "on" (busy ; signal), "reject" (busy signal), "silent" (ringer = silent) ;trustphoneip = no ; The phone has a ip address. It could be private, so if the phone is behind NAT ; we don't have to trust the phone ip address, but the ip address of the connection ;earlyrtp = none ; valid options: none, offhook, dial, ringout. default is none. ; The audio strem will be open in the progress and connected state. private = off ; permit the private function softkey for this device mwilamp = blink ; Set the MWI lamp style when MWI active to on, off, wink, flash or blink mwioncall = on ; Set the MWI on call. device => ATA13C4297AF101 ; device name SEP [lines] id = 101 ; future use pin = 101 ; future use label = Ext 101 ; button line label (7960, 7970, 7940, 7920) ;description = ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 101 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 101 ; caller id name cid_num = 101 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=ATA-186 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 101 id = 130 ; future use pin = 130 ; future use label = Ext 130 ; button line label (7960, 7970, 7940, 7920) description = Cisco 7970 ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 130 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 130 ; caller id name cid_num = 130 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 130 id = 131 ; future use pin = 131 ; future use label = Ext 131 ; button line label (7960, 7970, 7940, 7920) ;description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 131 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 131 ; caller id name cid_num = 131 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 131 id = 132 ; future use pin = 132 ; future use label = Ext 132 ; button line label (7960, 7970, 7940, 7920) ;description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 132 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 132 ; caller id name cid_num = 132 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 132 id = 133 ; future use pin = 133 ; future use label = Ext 133 ; button line label (7960, 7970, 7940, 7920) ;description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 133 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 133 ; caller id name cid_num = 133 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 133 id = 134 ; future use pin = 134 ; future use label = Ext 134 ; button line label (7960, 7970, 7940, 7920) description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 134 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Michael - SCCP ; caller id name cid_num = 134 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 134 id = 135 ; future use pin = 135 ; future use label = Ext 135 ; button line label (7960, 7970, 7940, 7920) description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 135 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Michael - SCCP ; caller id name cid_num = 135 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 135 id = 136 ; future use pin = 136 ; future use label = Ext 136 ; button line label (7960, 7970, 7940, 7920) ;description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 136 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 136 ; caller id name cid_num = 136 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 136 id = 137 ; future use pin = 137 ; future use label = Ext 137 ; button line label (7960, 7970, 7940, 7920) ;description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 137 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 137 ; caller id name cid_num = 137 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=7970 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 137 id = 138 ; future use pin = 138 ; future use label = Ext 138 ; button line label (7960, 7970, 7940, 7920) description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 138 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 138 ; caller id name cid_num = 138 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=ATA-186 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 138 id = 139 ; future use pin = 139 ; future use label = Ext 139 ; button line label (7960, 7970, 7940, 7920) description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 139 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 139 ; caller id name cid_num = 139 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=ATA-186 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 139 id = 140 ; future use pin = 140 ; future use label = Ext 140 ; button line label (7960, 7970, 7940, 7920) description = VoIP-4-U.CO.UK ; top display description context = from-internal incominglimit = 3 ; more than 1 incoming call = call waiting. transfer = on ; per line transfer capability. on, off, 1, 0 mailbox = 140 ; voicemail.conf (syntax: vmbox[@context][:folder]) vmnum = *97 ; speeddial for voicemail administration, just a number to dial cid_name = Ext 140 ; caller id name cid_num = 140 ;trnsfvm = 1000 ; extension to redirect the caller (e.g for voicemail) secondary_dialtone_digits = 9 ; digits for the secondary dialtone (max 9 digits) secondary_dialtone_tone = 0x22 ; outside dialtone musicclass=default ; Sets the default music on hold class language=en ; Default language setting accountcode=ATA-186 ; accountcode to ease billing ;rtptos = 184 ; sets the the rtp packets TOS for this line echocancel = off ; sets the phone echocancel for this line silencesuppression = off ; sets the silence suppression for this line callgroup = 1 ; We are in caller groups 1,3,4. Valid for this line pickupgroup = 1 ; We can do call pick-p for call group 1,3,4,5. Valid for this line ;amaflags = ; Sets the default AMA flag code stored in the CDR record for this line line => 140 ; phone types ; 12 -- Cisco IP Phone 12SP+ (or other 12 variants) ; 30 -- Cisco IP Phone 30VIP (or other 30 variants) ; 7902 -- Cisco IP Phone 7902G ; 7905 -- Cisco IP Phone 7905G ; 7910 -- Cisco IP Phone 7910 ; 7912 -- Cisco IP Phone 7912G ; 7935 -- Cisco IP Conference Station 7935 ; 7936 -- Cisco IP Conference Station 7936 ; 7920 -- Cisco IP Wireless Phone 7920 ; 7940 -- Cisco IP Phone 7940 ; 7960 -- Cisco IP Phone 7960 ; 7970 -- Cisco IP Phone 7970 ; 7914 -- Cisco IP Phone 7960 with a 7914 addon ; ata -- Cisco ATA-186 or Cisco ATA-188 ; kirk -- Kirk telecom ip phones