__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: RD-88F5181L-VOIP-GE LE U-Boot 1.1.1 (Mar 29 2006 - 03:28:49) Marvell version: 1.7.3 DRAM CS[0] base 0x00000000 size 32MB DRAM Total size 32MB [8192kB@ff800000] Flash: 8 MB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5181 B1 CPU: ARM926 (Rev 0) running @ 500Mhz SysClock = 166Mhz , TClock = 166Mhz USB 0: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Hit any key to stop autoboot: 0 Marvell>> Marvell>> Marvell>> ? ? - alias for 'help' FSdel - del a file from the Flash MV FS FSdir - ls the Flash MV FS FSformat- format the Flash MV FS FSlef - Load an exe file to the Flash MV FS FSlf - Load a file to the Flash MV FS FSrun - Load an exe file from the Flash MV FS and run it FStftp - tftp a file to the Flash MV FS FStftpe - tftp an exe file to the Flash MV FS FStype - cat file from the Flash MV FS base - print or set address offset boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootelf - Boot from an ELF image in memory bootext2 dev:boot_part1,boot_part2 addr boot_image linux_dev_name bootm - boot application image from memory bootp - boot image via network using BootP/TFTP protocol bootvx - Boot vxWorks from an ELF image bubt - Burn an image on the Boot Flash. chpart - change active partition cmp - memory compare cmpm - Compare Memory cp - memory copy cpumap - Display CPU memory mapping settings. crc32 - checksum calculation date - get/set/reset date & time dclk - Display the MV device CLKs. ddimm - Display SPD Dimm Info dhcp - invoke DHCP client to obtain IP/boot params diskboot- boot from IDE device dma - Perform DMA echo - echo args to console eeprom - EEPROM sub-system erase - erase FLASH memory ext2load- load binary file from a Ext2 filesystem ext2ls- list files in a directory (default /) fi - Find value in the memory. flinfo - print FLASH memory information fsinfo - print information about filesystems fsload - load binary file from a filesystem image g - start application at cached address 'addr'(default addr 0x40000) go - start application at address 'addr' help - print online help icrc32 - checksum calculation ide - IDE sub-system iloop - infinite loop on address range imd - i2c memory display imm - i2c memory modify (auto-incrementing) imw - memory write (fill) inm - memory modify (constant address) iprobe - probe to discover valid I2C chip addresses ir - reading and changing MV internal register values. ln - Load S-Record executable file through the network interface. loop - infinite loop on address range ls - list files in a directory (default /) map - Diasplay address decode windows md - memory display me - PCI master enable mm - memory modify (auto-incrementing) mp - map PCI BAR mtest - simple RAM test mw - memory write (fill) nm - memory modify (constant address) pci - list and access PCI Configuraton Space phyRead - Read Phy register phyWrite - Write Phy register ping - send ICMP ECHO_REQUEST to network host printenv- print environment variables protect - enable or disable FLASH write protection rarpboot- boot image via network using RARP/TFTP protocol reset - Perform RESET of the CPU resetenv - Return all environment variable to default. run - run commands in an environment variable saveenv - save environment variables to persistent storage se - PCI Slave enable setenv - set environment variables sg - scanning the PHYs status sleep - delay execution for some time sp - Scan PCI bus. tftpboot- boot image via network using TFTP protocol version - print monitor version Marvell>> boot ### JFFS2 loading 'uImage' to 0x400000 Scanning JFFS2 FS: ..... done. ### JFFS2 load complete: 885332 bytes loaded to 0x400000 ## Booting image at 00400000 ... Image Name: Linux-2.4.27-vrs1 Created: 2006-04-18 7:02:07 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 885268 Bytes = 864.5 kB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................. ZLinux version 2.4.27-vrs1 (joshua@localhost.localdomain) (gcc version 3.4.4 (r6 CPU: ARM926EJ-Sid(wb) revision 0 Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 166000000, Tclk = 166000000 - Warning - This LSP release was tested only with U-Boot release 1.7.0 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS0,115200 root=/dev/mtdblock1 rw ip=192.168.1.1e gppMask = [0x130] Calibrating delay loop... 331.77 BogoMIPS Memory: 32MB 0MB 0MB 0MB = 32MB total Memory: 30344KB available (1646K code, 311K data, 72K init) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) CPU: Testing write buffer: pass POSIX conformance testing by UNIFIX init hw started. PCI: bus0: Fast back to back transfers enabled No init hw. PCI: bus1: Fast back to back transfers enabled Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket bankwidth 2, base f4000000, size 1000000 Marvell Development Board (LSP Version 0.0.102)-- RD-88F5181L-VOIP-GE Detected Tclk 166000000 and SysClk 166000000 Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ed ttyS00 at 0xf1012000 (irq = 3) is a 16550A Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Loading network interface o Using switch header mode qdInit BoardID = eqdStart: CPU port 0x3 ----set PPU En Switch driver initialized Can't get netConfig: Use default UNM is not initialized yet 2 VLANs created: CpuPortMask = 0xa7 vid=0: DISABLED(0), portMask=0x750, portNum=5 vid=1: VLAN_1, portMask=0x04, portNum=1 vid=2: VLAN_2, portMask=0xa3, portNum=4 vid=12: ISOLATED(12), portMask=0x00, portNum=0 Port - Vlan 0 - VLAN_2 1 - VLAN_2 2 - VLAN_1 3 - VLAN_ALL 4 - DISABLED(0) 5 - VLAN_2 6 - DISABLED(0) 7 - VLAN_2 load virtual interface vid = 1 register if with name Init the hal : Ilegal MTU value 1500, rounding MTU to: 1506 if eth0 registered load virtual interface vid = 2 register if with name if eth1 registered PPP generic driver version 2.4.2 physmap flash device: 1000000 at f4000000 cfi_cmdset_0001: Erase suspend on write enabled Using buffer write method Using physmap partition definition Creating 6 MTD partitions on "phys_mapped_flash": 0x00000000-0x00600000 : "root" 0x00600000-0x00620000 : "nvram" 0x00620000-0x00640000 : "nvram default" 0x00640000-0x00660000 : "POT" 0x00660000-0x00680000 : "Traffic Meter" 0x00700000-0x00800000 : "uboot" Initializing Cryptographic API NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver Linux IP multicast router 0.06 plus PIM-SM ip_conntrack version 2.1 (8192 buckets, 65536 max) - 340 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_time loading NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 Fast Floating Point Emulator V0.94M by Peter Teichmann. cramfs: wrong magic VFS: Mounted root (jffs2 filesystem). Mounted devfs on /dev Freeing init memory: 72K 8Zinit: Missing PROCESS field in inittabinit: Missing PROCESS field in inittabi] Warning: loading gpio_module will taint the kernel: non-GPL license - Gemtek See http://www.tux.org/lkml/#export-tainted for information about tainted mods resetC.c :Parent process, pid = 22 resetC.c :Child process, pid = 26 Thu Jan 1 00:00:00 UTC 1970 (http)This is the parent process, pid = 24 # update nvram with default list! Init interfaces. can't get macaddr of ap0 (http)This is the child process, pid = 30 eth1: mac address changed device eth1 entered promiscuous mode SIOCSIFADDR: No such device SIOCGIFFLAGS: No such device interface ap0 does not exist! br0: port 1(eth1) entering listening state Init lan services. 00 , MBaker-T42(nvram_unset)exclusive zone shared_nvram->writing 1 Start UPnP route: resolving netmask route: resolving netmask route: resolving netmask route: resolving netmask route: resolving netmask Init wan. BusyBox v1.1.0 (2006.04.13-11:35+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. / # eth0: mac address changed eth0: Ilegal MTU value 1500, rounding MTU to: 1506 eth0: change mtu 1506 (buffer-size 1528) to 1506 (buffer-size 1528) total_entry is 0 httpd : This is httpd...ssl_enabled is 0