================= # ifconfig eth0 Link encap:Ethernet HWaddr 00:06:29:34:60:21 inet addr:192.168.0.4 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:183 errors:0 dropped:0 overruns:0 frame:0 TX packets:152 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19871 (19.4 KiB) TX bytes:20577 (20.0 KiB) Interrupt:10 ================= # lspci -v 00:02.0 Ethernet controller: Intel Corporation 82557/8/9 Ethernet Pro 100 (rev 08) Subsystem: Intel Corporation EtherExpress PRO/100+ Management Adapter Flags: bus master, medium devsel, latency 64, IRQ 10 Memory at f3efe000 (32-bit, non-prefetchable) [size=4K] I/O ports at 6c40 [size=64] Memory at f3f00000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at 20000000 [disabled] [size=1M] Capabilities: [dc] Power Management version 2 00:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21041 [Tulip Pass 3] (rev 21) Subsystem: D-Link System Inc DE-530+ Flags: bus master, medium devsel, latency 32, IRQ 6 I/O ports at 7c00 [size=128] Memory at f3efdf80 (32-bit, non-prefetchable) [size=128] Expansion ROM at 20100000 [disabled] [size=256K] ================= # dmesg Linux Tulip driver version 1.1.14 (May 11, 2002) eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin and others eth0: 0000:00:02.0, 00:06:29:34:60:21, IRQ 10. Receiver lock-up bug exists -- enabling work-around. Board assembly 713234-002, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0x04f4518b). Receiver lock-up workaround activated. natsemi dp8381x driver, version 2.1, Sept 11, 2006 originally by Donald Becker http://www.scyld.com/network/natsemi.html 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59. 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) 8139too Fast Ethernet driver 0.9.28 via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker pcnet32.c:v1.33-NAPI 27.Jun.2006 tsbogend@alpha.franken.de Intel(R) PRO/1000 Network Driver - version 7.3.15-k2 Copyright (c) 1999-2006 Intel Corporation. ns83820.c: National Semiconductor DP83820 10/100/1000 driver. ================= # cat /etc/rc.conf EXTIF=eth0 #EXTIP="192.168.25.2" #EXTNM="255.255.255.0" #EXTGW="192.168.25.1" #DNS="192.168.1.1 192.168.1.2 192.168.1.3" #NODHCP="$INT2IF" INTIF=eth1 INTIP=192.168.1.1 INTNM=255.255.255.0 DMZTYPE=extonly #DMZIF="eth2" #DMZIP="192.168.102.1" #DMZNM="255.255.255.0" #EXTPORTMAP="t222:192.168.111.17:22 u4569:192.168.111.12:4569" #EXTOPEN="t22 u4569" #NTPSERV="us.pool.ntp.org" NTPSERV="europe.pool.ntp.org" #NETMON=YES #CHKHOST="www.google.com" #CHKMETH="ICMP" # ICMP ping #CHKMETH="ARP" #arping (remember uses ARP - layer 2) #VOIPPORTS="5060 18000:20000" ##THIS IS VERY INSECURE, THIS SHOULD BE THE FIRST THING YOU DISABLE #ADNAME="AstLinux PBX" ================= # cat /etc/rc.modules # These modules get modprobe'd when the system starts up. #rtc #Comment out the modules you don't need, and change the order to #move eth0 to eth1, etc. #Ethernet support #10/100 first, then Gigabit 3c59x typhoon tulip eepro100 natsemi forcedeth 8139cp 8139too via-rhine pcnet32 acenic e1000 ns83820 r8169 tg3 sk98lin