Linux version 2.6.24 (2.6.24-2) (root@debian) (gcc version 4.2.3 (Debian 4.2.3-1)) #1 PREEMPT Tue Feb 5 02:44:22 CET 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
 BIOS-e820: 000000005fff0000 - 000000005fff3000 (ACPI NVS)
 BIOS-e820: 000000005fff3000 - 0000000060000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
639MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 393200) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   393200
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   393200
On node 0 totalpages: 393200
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 1279 pages used for memmap
  HighMem zone: 162545 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
DMI 2.2 present.
Allocating PCI resources starting at 70000000 (gap: 60000000:9ec00000)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 390129
Kernel command line: root=/dev/hdb1 ro acpi=off noapic nolapic selinux=0 vga=0x318 video=vesafb:mtrr:3,ywrap,vram:256
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1837.557 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1554904k/1572800k available (2442k kernel code, 16720k reserved, 798k data, 184k init, 655296k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffee000 - 0xfffff000   (  68 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc042e000 - 0xc045c000   ( 184 kB)
      .data : 0xc0362b9a - 0xc042a744   ( 798 kB)
      .text : 0xc0100000 - 0xc0362b9a   (2442 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 3676.44 BogoMIPS (lpj=1838223)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000420 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: AMD Athlon(tm) XP 2500+ stepping 00
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 0k freed
net_namespace: 64 bytes
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
PCI: Discovered primary peer bus ff [IRQ]
PCI: Using IRQ router default [10de/01e0] at 0000:00:00.0
PCI: Bridge: 0000:00:08.0
  IO window: d000-dfff
  MEM window: e7000000-e7ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: e4000000-e6ffffff
  PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
highmem bounce pool size: 64 pages
NTFS driver 2.1.29 [Flags: R/O].
fuse init (API version 7.9)
io scheduler noop registered
io scheduler cfq registered (default)
Boot video device is 0000:02:00.0
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 6144k, total 262144k
vesafb: mode is 1024x768x32, linelength=4096, pages=1
vesafb: protected mode interface info at c000:c2a0
vesafb: pmi: set display start = c00cc2d6, set palette = c00cc340
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=1536
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using get_cycles().
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
usbcore: registered new interface driver ub
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
PCI: Setting latency timer of device 0000:00:04.0 to 64
forcedeth 0000:00:04.0: ifname eth0, PHY OUI 0x20 @ 1, addr 00:0e:a6:66:de:e2
forcedeth 0000:00:04.0: timirq lnktim desc-v1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller (0x10de:0x0065 rev 0xa2) at  PCI slot 0000:00:09.0
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 6Y120L0, ATA DISK drive
hda: MAXTOR STM3160212A, ATA DISK drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/133 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: _NEC DVD_RW ND-4570A, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63
hda: cache flushes supported
 hda: hda1 hda2 < hda5 >
hdb: max request size: 128KiB
hdb: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63
hdb: cache flushes supported
 hdb: hdb1 hdb2 < hdb5 hdb6 > hdb3
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Driver 'sd' needs updating - please use bus_type methods
usbmon: debugfs is not available
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: irq 3, io mem 0xe8003000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 11, io mem 0xe8001000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 4, io mem 0xe8002000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
Clocksource tsc unstable (delta = 176845119 ns)
Time: pit clocksource has been installed.
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
logips2pp: Detected unknown logitech mouse model 90
input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with journal data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 184k freed
Linux video capture interface: v2.00
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5500
saa7130/34: v4l2 driver version 0.2.14 loaded
saa7133[0]: found at 0000:01:0a.0, rev: 240, irq: 7, latency: 32, mmio: 0xe7000000
saa7133[0]: subsystem: 1043:4845, board: ASUS TV-FM 7135 [card=53,autodetected]
saa7133[0]: board init: gpio is 0
saa7133[0]: i2c eeprom 00: 43 10 45 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: 00 ff e2 0f ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 04 08 ff 00 89 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 14 00 c2 96 ff 01 30 ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 2-004b: chip found @ 0x96 (saa7133[0])
tda8290 2-004b: setting tuner address to 61
tuner 2-004b: type set to tda8290+75
tda8290 2-004b: setting tuner address to 61
tuner 2-004b: type set to tda8290+75
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
snd-ca0106: Model 1006 Rev 00000000 Serial 10061102
Adding 465812k swap on /dev/hdb6.  Priority:-1 extents:1 across:465812k
EXT3 FS on hdb1, internal journal
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.