Initializing cgroup subsys cpuset
Linux version 2.6.24-1-686 (Debian 2.6.24-4) (waldi@debian.org) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Mon Feb 11 14:37:45 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001ffe0000 (usable)
 BIOS-e820: 000000001ffe0000 - 000000001fff8000 (ACPI data)
 BIOS-e820: 000000001fff8000 - 0000000020000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Entering add_active_range(0, 0, 131040) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   131040
  HighMem    131040 ->   131040
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   131040
On node 0 totalpages: 131040
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 991 pages used for memmap
  Normal zone: 125953 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000FF8F0, 0014 (r0 AMI   )
ACPI: RSDT 1FFF0000, 0028 (r1  INTEL SOLANO70 20010315 IMA        97)
ACPI: FACP 1FFF1000, 0074 (r1  INTEL SOLANO70 20010315 IMA        97)
ACPI: DSDT 1FFE0000, 3325 (r1  0AAVE 0AAVEP06    60100 MSFT  100000C)
ACPI: FACS 1FFF8000, 0040
ACPI: PM-Timer IO Port: 0x408
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130017
Kernel command line: root=/dev/hda1 ro vga=792 
Found and enabled local APIC!
mapped APIC to ffffb000 (fee00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 930.323 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 510700k/524160k available (1786k kernel code, 12868k reserved, 714k data, 248k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff4c000 - 0xfffff000   ( 716 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xe0800000 - 0xff7fe000   ( 495 MB)
    lowmem  : 0xc0000000 - 0xdffe0000   ( 511 MB)
      .init : 0xc0377000 - 0xc03b5000   ( 248 kB)
      .data : 0xc02be915 - 0xc0371384   ( 714 kB)
      .text : 0xc0100000 - 0xc02be915   (1786 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1862.37 BogoMIPS (lpj=3724759)
Security Framework initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: After generic identify, caps: 0387fbff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0e00)
CPU0: Intel Pentium III (Coppermine) stepping 0a
SMP motherboard not detected.
Brought up 1 CPUs
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdba1, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: tsc clocksource has been installed.
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x400-0x47f has been reserved
system 00:01: ioport range 0x480-0x4bf has been reserved
system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0c: ioport range 0x680-0x6ff has been reserved
system 00:0e: iomem range 0x0-0x9ffff could not be reserved
system 00:0e: iomem range 0xc0000-0xc7fff could not be reserved
system 00:0e: iomem range 0xcc000-0xfffff could not be reserved
system 00:0e: iomem range 0x100000-0x1fffffff could not be reserved
system 00:0e: iomem range 0x0-0x0 could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: c000-cfff
  MEM window: ff800000-ff8fffff
  PREFETCH window: ee900000-f69fffff
PCI: Bridge: 0000:00:1e.0
  IO window: d000-dfff
  MEM window: ff900000-ff9fffff
  PREFETCH window: f6a00000-f6afffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
 it is
Freeing initrd memory: 5238k freed
audit: initializing netlink socket (disabled)
audit(1202895034.424:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
vesafb: framebuffer at 0xf0000000, mapped to 0xe0880000, using 4608k, total 16384k
vesafb: mode is 1024x768x24, linelength=3072, pages=6
vesafb: protected mode interface info at c000:442f
vesafb: pmi: set display start = c00c449d, set palette = c00c44d7
vesafb: pmi: ports = c810 c816 c854 c838 c83c c85c c800 c804 c8b0 c8b2 c8b4 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 248k freed
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
3c59x: Donald Becker and others.
0000:02:0d.0: 3Com PCI 3c905C Tornado at e0816c00.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
PDC20262: IDE controller (0x105a:0x4d38 rev 0x01) at  PCI slot 0000:02:0f.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:0f.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PDC20262: 100% native mode on irq 11
PDC20262: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
    ide2: BM-DMA at 0xd400-0xd407, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xd408-0xd40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
libata version 3.00 loaded.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hde: CRD-8483B, ATAPI CD/DVD-ROM drive
hde: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hde: UDMA/33 mode selected
ide2 at 0xdc00-0xdc07,0xd882 on irq 11
Probing IDE interface ide3...
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 9, io base 0x0000e400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hde: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
ICH2: IDE controller (0x8086:0x244b rev 0x02) at  PCI slot 0000:00:1f.1
ICH2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
usb 1-1: new full speed USB device using uhci_hcd and address 2
hdb: WDC WD1200JB-00REA0, ATA DISK drive
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hda: WDC WD1200JB-00REA0, ATA DISK drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/100 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: WDC WD1200JB-00REA0, ATA DISK drive
hdc: ST3200822A, ATA DISK drive
hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdc: host side 80-wire cable detection failed, limiting max speed to UDMA33
hdc: UDMA/33 mode selected
hdd: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdd: host side 80-wire cable detection failed, limiting max speed to UDMA33
hdd: UDMA/33 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63
hda: cache flushes supported
 hda: hda1 hda2 < hda5 >
hdb: max request size: 512KiB
hdb: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63
hdb: cache flushes supported
 hdb: hdb1
hdc: max request size: 512KiB
hdc: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63
hdc: cache flushes supported
 hdc: hdc1
hdd: max request size: 512KiB
hdd: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63
hdd: cache flushes supported
 hdd: hdd1
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.102
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
agpgart: Detected an Intel i815 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
iTCO_wdt: No card detected
intel_rng: FWH not detected
input: PC Speaker as /class/input/input0
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
input: Power Button (FF) as /class/input/input1
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SPBT]
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
Real Time Clock Driver v1.12ac
parport_pc 00:0b: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
intel8x0_measure_ac97_clock: measured 53696 usecs
intel8x0: clocking to 48000
Adding 1510068k swap on /dev/hda5.  Priority:-1 extents:1 across:1510068k
EXT3 FS on hda1, internal journal
loop: module loaded
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdd1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0:  setting full-duplex.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
usb 1-1.1: new low speed USB device using uhci_hcd and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Logitech USB Receiver as /class/input/input3
input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1f.2-1.1
Fixing up Logitech keyboard report descriptor
input: Logitech USB Receiver as /class/input/input4
input,hiddev96,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1f.2-1.1
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
UDF-fs: No VRS found
hde: DMA read error
hde: DMA disabled
hde: media error (bad sector): status=0x51 { DriveReady SeekComplete Error }
hde: media error (bad sector): error=0x30 { LastFailedSense=0x03 }
ide: failed opcode was: unknown
ATAPI device hde:
  Error: Medium error -- (Sense key=0x03)
  (reserved error code) -- (asc=0x02, ascq=0x00)
  The failed "Read 10" packet command was: 
  "28 00 00 00 04 16 00 00 01 00 00 00 00 00 00 00 "
end_request: I/O error, dev hde, sector 4184
Buffer I/O error on device hde, logical block 1046
usb 1-1.4: new full speed USB device using uhci_hcd and address 4
usb 1-1.4: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 0:0:0:0: Direct-Access     WD       5000AAKB Externa l108 PQ: 0 ANSI: 0
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: [mac] sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
usb 1-1.4: reset full speed USB device using uhci_hcd and address 4
usb 1-1.4: reset full speed USB device using uhci_hcd and address 4
usb 1-1.4: reset full speed USB device using uhci_hcd and address 4
usb 1-1.4: reset full speed USB device using uhci_hcd and address 4
usb 1-1.4: reset full speed USB device using uhci_hcd and address 4
hfs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only.
hfs: write access to a jounaled filesystem is not supported, use the force option at your own risk, mounting read-only.
usb 1-1.4: USB disconnect, address 4
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver