[trixbox1.localdomain ~]# ztcfg -vv

Zaptel Version: 1.4.7.1-3259
Echo Canceller: OSLEC
Configuration
======================


Channel map:


0 channels to configure.

[trixbox1.localdomain ~]# wanrouter start

Error: Device wanpipe1 is already running
    Run 'wanrouter stop wanpipe1' first

Configuring interfaces: w1g1 w1g1: unknown interface: No such device

done.

[trixbox1.localdomain ~]# ztcfg   -vvv

Zaptel Version: 1.4.7.1-3259
Echo Canceller: OSLEC
Configuration
======================


Channel map:


0 channels to configure.

[trixbox1.localdomain ~]# amportal start


SETTING FILE PERMISSIONS
Permissions OK

STARTING ASTERISK
Asterisk is already running

STARTING FOP SERVER
FOP server is already running
[trixbox1.localdomain ~]# setup-sangoma

#############################################i##########################
#    Sangoma Wanpipe:  Zaptel/SMG/TDMAPI/BOOT Configuration Script     #
#                             v2.10                                    #
#                     Sangoma Technologies Inc.                        #
#                        Copyright(c) 2007.                            #
########################################################################


Generating configuration files for Trixbox
---------------------------------------------
Configuring T1/E1 cards [A101/A102/A104/A108]
---------------------------------------------
------------------------------------
Configuring ISDN BRI cards [A500]
------------------------------------

No Sangoma ISDN BRI cards detected

Press any key to continue:
------------------------------------
Configuring analog cards [A200/A400]
------------------------------------

-----------------------------------------------------------
A200 detected on slot:6 bus:2
-----------------------------------------------------------
Which codec will be used?
 1. MULAW - North America
 2. ALAW - Europe
[1-2]:1

A200 configured on slot:6 bus:2 span:1
Press any key to continue:

Analog card configuration complete

Press any key to continue:

###################################################################
#                             SUMMARY                             #
###################################################################

  0 T1/E1 port(s) detected, 0 configured
  0 ISDN BRI port(s) detected, 0 configured
  1 analog card(s) detected, 1 configured

Configurator has created the following files:
        1. Wanpipe config files in /etc/wanpipe
        2. Zaptel config file /etc/zaptel.conf
        3. Zapata config file /etc/asterisk/zapata-auto.conf


Your original configuration files will be saved to:
        1. /etc/zaptel.conf.bak
        2. /etc/asterisk/zapata-auto.conf.bak


Your configuration has been saved in /etc/wanpipe/debug-2008-03-03.tgz.
When requesting support, email this file to techdesk@sangoma.com

Press any key to continue:

Zaptel and Wanpipe configuration complete: choose action
 1. Save cfg: Restart Asterisk & Wanpipe now
 2. Save cfg: Restart Asterisk & Wanpipe when convenient
 3. Save cfg: Stop Asterisk & Wanpipe now
 4. Save cfg: Stop Asterisk & Wanpipe when convenient
 5. Do not save cfg: Exit
[1-5]:1




STOPPING ASTERISK

Disconnected from Asterisk server
Asterisk Stopped

STOPPING FOP SERVER
FOP Server Stopped
FATAL: Module zaptel is in use.
Error executing command:
modprobe -r zaptel

Would you like to continue?
 1. No - exit
 2. YES
[1-2, ENTER='No']:2


Stopping Wanpipe...


Shutting down wanpipe1 interface: w1g1
w1g1: unknown interface: No such device
Shutting down device: wanpipe1
No devices running, Unloading Modules


Unloading Zaptel modules...

Removing old configuration files...

Copying new Wanpipe configuration files...

Copying new Zaptel configuration file (/etc/zaptel.conf)...

Copying new chan_zap configuration files (/etc/asterisk/zapata-auto.conf)...

Starting Wanpipe...

Starting WAN Router...
Loading WAN drivers: wanpipe done.
Starting up device: wanpipe1
Configuring interfaces: w1g1 w1g1: unknown interface: No such device

done.

Loading Zaptel...

Zaptel Version: 1.4.7.1-3259
Echo Canceller: OSLEC
Configuration
======================


0 channels to configure.


Starting Amportal...


SETTING FILE PERMISSIONS
Permissions OK

STARTING ASTERISK
Asterisk Started

STARTING FOP SERVER
FOP Server Started

Wanrouter start complete...
Current boot level is 3

Wanrouter boot scripts configuration...

Removing existing wanrouter boot scripts...OK
Would you like wanrouter to start on system boot?
 1. YES
 2. NO
[1-2]:1

Verifying Zaptel boot scripts...Enabled (level:09)
Verifying Zaptel shutdown scripts...Enabled (level:92)
Enabling wanrouter boot scripts ...(level:8)
Enabling wanrouter shutdown scripts ...(level:91)
Sangoma cards configuration complete, exiting...