Section "ServerLayout" Identifier "Simple Layout" Screen "Screen 1" InputDevice "Mouse1" "CorePointer" InputDevice "Keyboard1" "CoreKeyboard" EndSection Section "Files" RgbPath "/usr/X11R6/lib/X11/rgb" FontPath "/usr/share/fonts/misc/" FontPath "/usr/share/fonts/TTF/" FontPath "/usr/share/fonts/Type1/" # FontPath "/usr/share/fonts/CID/" FontPath "/usr/share/fonts/75dpi/" FontPath "/usr/share/fonts/100dpi/" # FontPath "/usr/share/fonts/local/" # FontPath "/usr/share/fonts/Speedo/" # FontPath "/usr/share/fonts/TrueType/" # FontPath "/usr/share/fonts/freefont/" # The module search path. The default path is shown here. # ModulePath "/usr/X11R6/lib/modules" EndSection Section "Module" # This loads the DBE extension module. Load "dbe" # Double buffer extension Load "v4l" # This loads the miscellaneous extensions module, and disables # initialisation of the XFree86-DGA extension within that module. SubSection "extmod" Option "omit xfree86-dga" # don't initialise the DGA extension EndSubSection # This loads the font modules Load "type1" # Load "speedo" Load "freetype" # Load "xtt" # This loads the GLX module Load "glx" # This loads the DRI module # Load "dri" EndSection # ********************************************************************** # Files section. This allows default font and rgb paths to be set # ********************************************************************** # ********************************************************************** # Server flags section. # ********************************************************************** Section "ServerFlags" # Uncomment this to cause a core dump at the spot where a signal is # received. This may leave the console in an unusable state, but may # provide a better stack trace in the core dump to aid in debugging # Option "NoTrapSignals" # Uncomment this to disable the VT switch sequence # (where n is 1 through 12). This allows clients to receive these key # events. # Option "DontVTSwitch" # Uncomment this to disable the server abort sequence # This allows clients to receive this key event. # Option "DontZap" # Uncomment this to disable the / mode switching # sequences. This allows clients to receive these key events. # Option "Dont Zoom" # Uncomment this to disable tuning with the xvidtune client. With # it the client can still run and fetch card and monitor attributes, # but it will not be allowed to change them. If it tries it will # receive a protocol error. # Option "DisableVidModeExtension" # Uncomment this to enable the use of a non-local xvidtune client. # Option "AllowNonLocalXvidtune" # Uncomment this to disable dynamically modifying the input device # (mouse and keyboard) settings. # Option "DisableModInDev" # Uncomment this to enable the use of a non-local client to # change the keyboard or mouse settings (currently only xset). # Option "AllowNonLocalModInDev" EndSection Section "InputDevice" Identifier "Keyboard1" Driver "kbd" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) # Option "Xleds" "1 2 3" # Option "LeftAlt" "Meta" # Option "RightAlt" "ModeShift" # To customise the XKB settings to suit your keyboard, modify the # lines below (which are the defaults). For example, for a non-U.S. # keyboard, you will probably want to use: # Option "XkbModel" "pc102" # If you have a US Microsoft Natural keyboard, you can use: # Option "XkbModel" "microsoft" # # Then to change the language, change the Layout setting. # For example, a german layout can be obtained with: # Option "XkbLayout" "de" # or: # Option "XkbLayout" "de" # Option "XkbVariant" "nodeadkeys" # # If you'd like to switch the positions of your capslock and # control keys, use: Option "XkbOptions" "ctrl:swapcaps" # These are the default XKB settings for Xorg # Option "XkbRules" "xorg" # Option "XkbModel" "pc101" # Option "XkbLayout" "us" # Option "XkbVariant" "" # Option "XkbOptions" "" # Option "XkbDisable" Option "XkbRules" "xorg" Option "XkbModel" "pc104" Option "XkbLayout" "us" EndSection Section "InputDevice" # Identifier and driver Driver "mouse" Identifier "Mouse1" # Option "Protocol" "Auto" Option "Protocol" "ExplorerPS/2" Option "Device" "/dev/mouse" Option "Buttons" "7" Option "ZAxisMapping" "4 5" # Mouse-speed setting for PS/2 mouse. Option "Resolution" "800" # When using XQUEUE, comment out the above two lines, and uncomment # the following line. # Option "Protocol" "Xqueue" # Baudrate and SampleRate are only for some Logitech mice. In # almost every case these lines should be omitted. # Option "BaudRate" "9600" # Option "SampleRate" "150" # Emulate3Buttons is an option for 2-button Microsoft mice # Emulate3Timeout is the timeout in milliseconds (default is 50ms) # Option "Emulate3Buttons" # Option "Emulate3Timeout" "50" # ChordMiddle is an option for some 3-button Logitech mice # Option "ChordMiddle" EndSection # ********************************************************************** # Other input device sections # this is optional and is required only if you # are using extended input devices. This is for example only. Refer # to the xorg.conf man page for a description of the options. # ********************************************************************** # # Section "InputDevice" # Identifier "Mouse2" # Driver "mouse" # Option "Protocol" "MouseMan" # Option "Device" "/dev/mouse2" # EndSection # # Section "InputDevice" # Identifier "spaceball" # Driver "magellan" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "spaceball2" # Driver "spaceorb" # Option "Device" "/dev/cua0" # EndSection # # Section "InputDevice" # Identifier "touchscreen0" # Driver "microtouch" # Option "Device" "/dev/ttyS0" # Option "MinX" "1412" # Option "MaxX" "15184" # Option "MinY" "15372" # Option "MaxY" "1230" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # # Section "InputDevice" # Identifier "touchscreen1" # Driver "elo2300" # Option "Device" "/dev/ttyS0" # Option "MinX" "231" # Option "MaxX" "3868" # Option "MinY" "3858" # Option "MaxY" "272" # Option "ScreenNumber" "0" # Option "ReportingMode" "Scaled" # Option "ButtonThreshold" "17" # Option "ButtonNumber" "1" # Option "SendCoreEvents" # EndSection # ********************************************************************** # Monitor section # ********************************************************************** # Any number of monitor sections may be present Section "Monitor" Identifier "60" # HorizSync is in kHz unless units are specified. # HorizSync may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. HorizSync 30-96 # HorizSync 30-64 # multisync # HorizSync 31.5, 35.2 # multiple fixed sync frequencies # HorizSync 15-25, 30-50 # multiple ranges of sync frequencies # VertRefresh is in Hz unless units are specified. # VertRefresh may be a comma separated list of discrete values, or a # comma separated list of ranges of values. # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S # USER MANUAL FOR THE CORRECT NUMBERS. VertRefresh 50-160 EndSection # ********************************************************************** # Graphics device section # ********************************************************************** # Any number of graphics device sections may be present # Standard VGA Device: # Device configured by xorgconfig: Section "Device" Identifier "** NVIDIA (generic) [nv]" Driver "nvidia" #VideoRam 131072 # Insert Clocks lines here if appropriate EndSection # ********************************************************************** # Screen sections # ********************************************************************** # Any number of screen sections may be present. Each describes # the configuration of a single screen. A single specific screen section # may be specified from the X server command line with the "-screen" # option. Section "Screen" Identifier "Screen 1" Device "** NVIDIA (generic) [nv]" Monitor "60" DefaultDepth 24 # Subsection "Display" # Depth 16 # Modes "1280x1024" "1024x768" "800x600" "640x480" # ViewPort 0 0 # EndSubsection Subsection "Display" Depth 24 Modes "CRT-0: 1600x1200, 1280x1024,1024x768,800x600,640x480" ViewPort 0 0 EndSubsection EndSection # ********************************************************************** # ServerLayout sections. # ********************************************************************** # Any number of ServerLayout sections may be present. Each describes # the way multiple screens are organised. A specific ServerLayout # section may be specified from the X server command line with the # "-layout" option. In the absence of this, the first section is used. # When now ServerLayout section is present, the first Screen section # is used alone. # Section "DRI" # Mode 0666 # EndSection