itgen-admin@interserv:~$ dmesg [ 0.000000] Linux version 2.6.22-14-generic (buildd@terranova) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Feb 12 07:42:25 UTC 2008 (Ubuntu 2.6.22-14.52-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable) [ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable) [ 0.000000] BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data) [ 0.000000] BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved) [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000120000000 (usable) [ 0.000000] Warning only 4GB will be used. [ 0.000000] Use a PAE enabled kernel. [ 0.000000] 3200MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f5b70 [ 0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 1048576 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 1048576 [ 0.000000] On node 0 totalpages: 1048576 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 6400 pages used for memmap [ 0.000000] HighMem zone: 812800 pages, LIFO batch:31 [ 0.000000] DMI 2.4 present. [ 0.000000] ACPI: RSDP signature @ 0xC00F7C20 checksum 0 [ 0.000000] ACPI: RSDP 000F7C20, 0024 (r2 Nvidia) [ 0.000000] ACPI: XSDT DFEE3100, 0044 (r1 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP DFEEC5C0, 00F4 (r3 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT DFEE3280, 92C4 (r1 NVIDIA AWRDACPI 1000 MSFT 3000000) [ 0.000000] ACPI: FACS DFEE0000, 0040 [ 0.000000] ACPI: HPET DFEEC7C0, 0038 (r1 Nvidia ASUSACPI 42302E31 AWRD 98) [ 0.000000] ACPI: MCFG DFEEC840, 003C (r1 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] ACPI: APIC DFEEC700, 007C (r1 Nvidia ASUSACPI 42302E31 AWRD 0) [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:11 APIC version 16 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 15:11 APIC version 16 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfefff000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at e0000000 (gap: dff00000:10100000) [ 0.000000] Built 1 zonelists. Total pages: 1040384 [ 0.000000] Kernel command line: root=/dev/mapper/interserv-root ro quiet splash [ 0.000000] mapped APIC to ffffd000 (fee00000) [ 0.000000] mapped IOAPIC to ffffc000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2511.593 MHz processor. [ 0.000000] spurious 8259A interrupt: IRQ7. [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 3622512k/4194304k available (2015k kernel code, 45124k reserved, 915k data, 364k init, 2751360k highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB) [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.000000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 0.000000] .init : 0xc03e3000 - 0xc043e000 ( 364 kB) [ 0.000000] .data : 0xc02f7e86 - 0xc03dce84 ( 915 kB) [ 0.000000] .text : 0xc0100000 - 0xc02f7e86 (2015 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 0.000000] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 0.000000] hpet0: at MMIO 0xfefff000, IRQs 2, 8, 31 [ 0.000000] hpet0: 3 32-bit timers, 25000000 Hz [ 0.080000] Calibrating delay using timer specific routine.. 5026.96 BogoMIPS (lpj=10053932) [ 0.080000] Security Framework v1.0.0 initialized [ 0.080000] SELinux: Disabled at boot. [ 0.080000] Mount-cache hash table entries: 512 [ 0.080000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f [ 0.080000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.080000] CPU: L2 Cache: 512K (64 bytes/line) [ 0.080000] CPU 0(2) -> Core 0 [ 0.080000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f [ 0.080000] Compat vDSO mapped to ffffe000. [ 0.080000] Checking 'hlt' instruction... OK. [ 0.096000] SMP alternatives: switching to UP code [ 0.096000] Early unpacking initramfs... done [ 0.340000] ACPI: Core revision 20070126 [ 0.340000] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 0.344000] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ stepping 02 [ 0.344000] SMP alternatives: switching to SMP code [ 0.344000] Booting processor 1/1 eip 3000 [ 0.352000] Initializing CPU#1 [ 0.436000] Calibrating delay using timer specific routine.. 5023.17 BogoMIPS (lpj=10046346) [ 0.436000] CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000011f [ 0.436000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.436000] CPU: L2 Cache: 512K (64 bytes/line) [ 0.436000] CPU 1(2) -> Core 1 [ 0.436000] CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000011f [ 0.436000] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ stepping 02 [ 0.436000] Total of 2 processors activated (10050.13 BogoMIPS). [ 0.436000] ENABLING IO-APIC IRQs [ 0.436000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.476000] Brought up 2 CPUs [ 0.508000] migration_cost=4000 [ 0.508000] Booting paravirtualized kernel on bare hardware [ 0.508000] Time: 23:21:47 Date: 03/07/108 [ 0.508000] NET: Registered protocol family 16 [ 0.508000] EISA bus registered [ 0.508000] ACPI: bus type pci registered [ 0.540000] PCI: PCI BIOS revision 3.00 entry at 0xf2380, last bus=3 [ 0.540000] PCI: Using configuration type 1 [ 0.540000] Setting up standard PCI resources [ 0.544000] ACPI: EC: Look up EC in DSDT [ 0.552000] ACPI: Interpreter enabled [ 0.552000] ACPI: (supports S0 S1 S3 S4 S5) [ 0.552000] ACPI: Using IOAPIC for interrupt routing [ 0.560000] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.560000] PCI: Probing PCI hardware (bus 00) [ 0.560000] PCI: Transparent bridge - 0000:00:06.0 [ 0.560000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.560000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 0.608000] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.608000] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.608000] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.608000] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.608000] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.608000] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 *10 11 14 15) [ 0.608000] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15) [ 0.608000] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15) [ 0.612000] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0 [ 0.612000] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0 [ 0.612000] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. [ 0.612000] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 [ 0.612000] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 [ 0.616000] ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0 [ 0.616000] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. [ 0.616000] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0 [ 0.616000] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 [ 0.616000] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 [ 0.616000] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. [ 0.616000] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. [ 0.616000] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 [ 0.616000] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 [ 0.616000] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0 [ 0.616000] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.616000] pnp: PnP ACPI init [ 0.616000] ACPI: bus type pnp registered [ 0.620000] pnp: PnP ACPI: found 13 devices [ 0.620000] ACPI: ACPI bus type pnp unregistered [ 0.620000] PnPBIOS: Disabled by ACPI PNP [ 0.620000] PCI: Using ACPI for IRQ routing [ 0.620000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 0.664000] NET: Registered protocol family 8 [ 0.664000] NET: Registered protocol family 20 [ 0.664000] pnp: 00:01: ioport range 0x1000-0x107f has been reserved [ 0.664000] pnp: 00:01: ioport range 0x1080-0x10ff has been reserved [ 0.664000] pnp: 00:01: ioport range 0x1400-0x147f has been reserved [ 0.664000] pnp: 00:01: ioport range 0x1480-0x14ff has been reserved [ 0.664000] pnp: 00:01: ioport range 0x1800-0x187f has been reserved [ 0.664000] pnp: 00:01: ioport range 0x1880-0x18ff has been reserved [ 0.664000] pnp: 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved [ 0.664000] pnp: 00:0c: iomem range 0xd2800-0xd3fff has been reserved [ 0.664000] pnp: 00:0c: iomem range 0xf0000-0xf7fff could not be reserved [ 0.664000] pnp: 00:0c: iomem range 0xf8000-0xfbfff could not be reserved [ 0.664000] pnp: 00:0c: iomem range 0xfc000-0xfffff could not be reserved [ 0.668000] Time: hpet clocksource has been installed. [ 0.668000] Switched to high resolution mode on CPU 0 [ 0.668000] Switched to high resolution mode on CPU 1 [ 0.692000] PCI: Bridge: 0000:00:06.0 [ 0.692000] IO window: disabled. [ 0.692000] MEM window: fde00000-fdefffff [ 0.692000] PREFETCH window: disabled. [ 0.692000] PCI: Bridge: 0000:00:0e.0 [ 0.692000] IO window: 8000-9fff [ 0.692000] MEM window: fdd00000-fddfffff [ 0.692000] PREFETCH window: disabled. [ 0.692000] PCI: Bridge: 0000:00:0f.0 [ 0.692000] IO window: disabled. [ 0.692000] MEM window: fa000000-fcffffff [ 0.692000] PREFETCH window: e0000000-efffffff [ 0.692000] PCI: Setting latency timer of device 0000:00:06.0 to 64 [ 0.692000] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 0.692000] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 0.692000] NET: Registered protocol family 2 [ 0.732000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.732000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 0.732000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.732000] TCP: Hash tables configured (established 131072 bind 65536) [ 0.732000] TCP reno registered [ 0.748000] checking if image is initramfs... it is [ 1.228000] Freeing initrd memory: 7595k freed [ 1.228000] audit: initializing netlink socket (disabled) [ 1.228000] audit(1207610507.168:1): initialized [ 1.228000] highmem bounce pool size: 64 pages [ 1.228000] VFS: Disk quotas dquot_6.5.1 [ 1.228000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.228000] io scheduler noop registered [ 1.228000] io scheduler anticipatory registered [ 1.228000] io scheduler deadline registered [ 1.228000] io scheduler cfq registered (default) [ 1.248000] Boot video device is 0000:03:00.0 [ 1.248000] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 1.248000] assign_interrupt_mode Found MSI capability [ 1.248000] Allocate Port Service[0000:00:0e.0:pcie00] [ 1.248000] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 1.248000] assign_interrupt_mode Found MSI capability [ 1.248000] Allocate Port Service[0000:00:0f.0:pcie00] [ 1.248000] isapnp: Scanning for PnP cards... [ 1.600000] isapnp: No Plug & Play device found [ 1.616000] Real Time Clock Driver v1.12ac [ 1.616000] hpet_resources: 0xfefff000 is busy [ 1.616000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 1.616000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.616000] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.616000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 1.616000] input: Macintosh mouse button emulation as /class/input/input0 [ 1.616000] PNP: No PS/2 controller found. Probing ports directly. [ 1.616000] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.616000] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.616000] mice: PS/2 mouse device common for all mice [ 1.616000] EISA: Probing bus 0 at eisa.0 [ 1.616000] Cannot allocate resource for EISA slot 1 [ 1.616000] Cannot allocate resource for EISA slot 8 [ 1.616000] EISA: Detected 0 cards. [ 1.616000] TCP cubic registered [ 1.616000] NET: Registered protocol family 1 [ 1.616000] Using IPI No-Shortcut mode [ 1.616000] Magic number: 4:775:402 [ 1.616000] hash matches device 0000:03:00.0 [ 1.616000] Freeing unused kernel memory: 364k freed [ 2.800000] fuse init (API version 7.8) [ 2.804000] Capability LSM initialized [ 2.808000] ACPI: Fan [FAN] (on) [ 2.812000] ACPI: Thermal Zone [THRM] (40 C) [ 2.824000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 2.836000] md: linear personality registered for level -1 [ 2.840000] md: multipath personality registered for level -4 [ 2.840000] md: raid0 personality registered for level 0 [ 2.844000] md: raid1 personality registered for level 1 [ 2.848000] raid5: automatically using best checksumming function: pIII_sse [ 2.868000] pIII_sse : 7648.000 MB/sec [ 2.868000] raid5: using function: pIII_sse (7648.000 MB/sec) [ 2.936000] raid6: int32x1 1069 MB/s [ 3.004000] raid6: int32x2 1093 MB/s [ 3.072000] raid6: int32x4 919 MB/s [ 3.140000] raid6: int32x8 655 MB/s [ 3.208000] raid6: mmxx1 2012 MB/s [ 3.276000] raid6: mmxx2 3723 MB/s [ 3.344000] raid6: sse1x1 2016 MB/s [ 3.412000] raid6: sse1x2 3375 MB/s [ 3.480000] raid6: sse2x1 3396 MB/s [ 3.548000] raid6: sse2x2 4685 MB/s [ 3.548000] raid6: using algorithm sse2x2 (4685 MB/s) [ 3.548000] md: raid6 personality registered for level 6 [ 3.548000] md: raid5 personality registered for level 5 [ 3.548000] md: raid4 personality registered for level 4 [ 3.564000] md: raid10 personality registered for level 10 [ 4.012000] SCSI subsystem initialized [ 4.016000] libata version 2.21 loaded. [ 4.016000] sata_nv 0000:00:05.0: version 3.4 [ 4.020000] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23 [ 4.020000] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 16 [ 4.020000] PCI: Setting latency timer of device 0000:00:05.0 to 64 [ 4.020000] scsi0 : sata_nv [ 4.020000] scsi1 : sata_nv [ 4.020000] ata1: SATA max UDMA/133 cmd 0x000109f0 ctl 0x00010bf2 bmdma 0x0001dc00 irq 16 [ 4.020000] ata2: SATA max UDMA/133 cmd 0x00010970 ctl 0x00010b72 bmdma 0x0001dc08 irq 16 [ 4.040000] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60. [ 4.060000] usbcore: registered new interface driver usbfs [ 4.060000] usbcore: registered new interface driver hub [ 4.060000] usbcore: registered new device driver usb [ 4.060000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.088000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 4.088000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 4.116000] Floppy drive(s): fd0 is 1.44M [ 4.140000] FDC 0 is a post-1991 82077 [ 4.488000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.512000] ata1.00: ATA-8: SAMSUNG HD320KJ, CP100-12, max UDMA7 [ 4.512000] ata1.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 0/32) [ 4.520000] ata1.00: configured for UDMA/133 [ 4.988000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.012000] ata2.00: ATA-8: SAMSUNG HD320KJ, CP100-12, max UDMA7 [ 5.012000] ata2.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 0/32) [ 5.020000] ata2.00: configured for UDMA/133 [ 5.020000] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD320KJ CP10 PQ: 0 ANSI: 5 [ 5.020000] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD320KJ CP10 PQ: 0 ANSI: 5 [ 5.020000] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22 [ 5.020000] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 17 [ 5.020000] PCI: Setting latency timer of device 0000:00:05.1 to 64 [ 5.020000] scsi2 : sata_nv [ 5.020000] scsi3 : sata_nv [ 5.020000] ata3: SATA max UDMA/133 cmd 0x000109e0 ctl 0x00010be2 bmdma 0x0001c800 irq 17 [ 5.020000] ata4: SATA max UDMA/133 cmd 0x00010960 ctl 0x00010b62 bmdma 0x0001c808 irq 17 [ 5.488000] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.512000] ata3.00: ATA-8: SAMSUNG HD320KJ, CP100-12, max UDMA7 [ 5.512000] ata3.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 0/32) [ 5.520000] ata3.00: configured for UDMA/133 [ 5.988000] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 6.152000] ata4.00: ATAPI: HL-DT-ST DVDRAM GH20NS10, EL00, max UDMA/100 [ 6.324000] ata4.00: configured for UDMA/100 [ 6.324000] scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD320KJ CP10 PQ: 0 ANSI: 5 [ 6.324000] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GH20NS10 EL00 PQ: 0 ANSI: 5 [ 6.324000] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21 [ 6.324000] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 21 (level, low) -> IRQ 18 [ 6.324000] PCI: Setting latency timer of device 0000:00:05.2 to 64 [ 6.324000] scsi4 : sata_nv [ 6.328000] scsi5 : sata_nv [ 6.328000] ata5: SATA max UDMA/133 cmd 0x0001c400 ctl 0x0001c002 bmdma 0x0001b400 irq 18 [ 6.328000] ata6: SATA max UDMA/133 cmd 0x0001bc00 ctl 0x0001b802 bmdma 0x0001b408 irq 18 [ 6.640000] ata5: SATA link down (SStatus 0 SControl 300) [ 6.960000] ata6: SATA link down (SStatus 0 SControl 300) [ 6.968000] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20 [ 6.968000] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 19 [ 6.968000] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 6.968000] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 6.968000] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 6.968000] ehci_hcd 0000:00:02.1: debug port 1 [ 6.968000] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 6.968000] ehci_hcd 0000:00:02.1: irq 19, io mem 0xfe02e000 [ 6.968000] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 6.968000] usb usb1: configuration #1 chosen from 1 choice [ 6.968000] hub 1-0:1.0: USB hub found [ 6.968000] hub 1-0:1.0: 10 ports detected [ 6.968000] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 [ 6.968000] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 20 [ 7.020000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[fdeff000-fdeff7ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 7.072000] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 [ 7.072000] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 16 [ 7.072000] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 7.072000] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 7.072000] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 [ 7.072000] ohci_hcd 0000:00:02.0: irq 16, io mem 0xfe02f000 [ 7.128000] usb usb2: configuration #1 chosen from 1 choice [ 7.128000] hub 2-0:1.0: USB hub found [ 7.128000] hub 2-0:1.0: 10 ports detected [ 7.232000] NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0 [ 7.232000] NFORCE-MCP55: chipset revision 161 [ 7.232000] NFORCE-MCP55: not 100% native mode: will probe irqs later [ 7.232000] NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller [ 7.232000] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA [ 7.232000] Probing IDE interface ide0... [ 7.744000] usb 2-3: new low speed USB device using ohci_hcd and address 2 [ 7.800000] PCI: Enabling device 0000:02:00.1 (0000 -> 0001) [ 7.800000] ACPI: PCI Interrupt Link [APC8] enabled at IRQ 16 [ 7.800000] ACPI: PCI Interrupt 0000:02:00.1[B] -> Link [APC8] -> GSI 16 (level, low) -> IRQ 21 [ 7.800000] PCI: Setting latency timer of device 0000:02:00.1 to 64 [ 7.800000] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 [ 7.800000] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APCH] -> GSI 22 (level, low) -> IRQ 17 [ 7.800000] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 7.800000] forcedeth: using HIGHDMA [ 7.800000] scsi6 : pata_jmicron [ 7.800000] scsi7 : pata_jmicron [ 7.800000] ata7: PATA max UDMA/100 cmd 0x00019c00 ctl 0x00019802 bmdma 0x00018c00 irq 21 [ 7.800000] ata8: PATA max UDMA/100 cmd 0x00019400 ctl 0x00019002 bmdma 0x00018c08 irq 21 [ 7.956000] usb 2-3: configuration #1 chosen from 1 choice [ 8.264000] usb 2-4: new low speed USB device using ohci_hcd and address 3 [ 8.292000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800018a845f] [ 8.320000] eth0: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:08.0 [ 8.320000] ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 21 [ 8.320000] ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [AMC1] -> GSI 21 (level, low) -> IRQ 18 [ 8.320000] PCI: Setting latency timer of device 0000:00:09.0 to 64 [ 8.320000] forcedeth: using HIGHDMA [ 8.472000] usb 2-4: configuration #1 chosen from 1 choice [ 8.476000] usbcore: registered new interface driver hiddev [ 8.484000] input: Microsoft Microsoft Optical Mouse by Starck as /class/input/input1 [ 8.484000] input: USB HID v1.10 Mouse [Microsoft Microsoft Optical Mouse by Starck] on usb-0000:00:02.0-3 [ 8.488000] input: USB-compliant keyboard as /class/input/input2 [ 8.488000] input: USB HID v1.10 Keyboard [USB-compliant keyboard] on usb-0000:00:02.0-4 [ 8.500000] input: USB-compliant keyboard as /class/input/input3 [ 8.500000] input,hiddev96: USB HID v1.10 Mouse [USB-compliant keyboard] on usb-0000:00:02.0-4 [ 8.500000] usbcore: registered new interface driver usbhid [ 8.500000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 8.840000] eth1: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:09.0 [ 8.840000] ahci 0000:02:00.0: version 2.2 [ 8.840000] ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16 [ 8.840000] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 21 [ 8.844000] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) [ 8.844000] sd 0:0:0:0: [sda] Write Protect is off [ 8.844000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8.844000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.844000] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) [ 8.844000] sd 0:0:0:0: [sda] Write Protect is off [ 8.844000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 8.844000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.844000] sda: sda1 sda2 < sda5 > [ 8.912000] sd 0:0:0:0: [sda] Attached SCSI disk [ 8.912000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 8.912000] sd 1:0:0:0: [sdb] Write Protect is off [ 8.912000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 8.912000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.912000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 8.912000] sd 1:0:0:0: [sdb] Write Protect is off [ 8.912000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 8.912000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.912000] sdb: [ 8.956000] sd 1:0:0:0: [sdb] Attached SCSI disk [ 8.956000] sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) [ 8.956000] sd 2:0:0:0: [sdc] Write Protect is off [ 8.956000] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 8.956000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.956000] sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) [ 8.956000] sd 2:0:0:0: [sdc] Write Protect is off [ 8.956000] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 8.956000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 8.956000] sdc: sdc1 [ 8.980000] sd 2:0:0:0: [sdc] Attached SCSI disk [ 8.984000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 8.984000] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 8.984000] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 8.984000] sr 3:0:0:0: Attached scsi generic sg3 type 5 [ 9.004000] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 9.004000] Uniform CD-ROM driver Revision: 3.20 [ 9.004000] sr 3:0:0:0: Attached scsi CD-ROM sr0 [ 9.844000] ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode [ 9.844000] ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part [ 9.844000] PCI: Setting latency timer of device 0000:02:00.0 to 64 [ 9.844000] scsi8 : ahci [ 9.844000] scsi9 : ahci [ 9.844000] ata9: SATA max UDMA/133 cmd 0xf8964100 ctl 0x00000000 bmdma 0x00000000 irq 21 [ 9.844000] ata10: SATA max UDMA/133 cmd 0xf8964180 ctl 0x00000000 bmdma 0x00000000 irq 21 [ 10.156000] ata9: SATA link down (SStatus 0 SControl 300) [ 10.468000] ata10: SATA link down (SStatus 0 SControl 300) [ 10.592000] Attempting manual resume [ 10.592000] swsusp: Resume From Partition 254:1 [ 10.592000] PM: Checking swsusp image. [ 10.592000] PM: Resume from disk failed. [ 10.640000] kjournald starting. Commit interval 5 seconds [ 10.640000] EXT3-fs: mounted filesystem with ordered data mode. [ 16.376000] NET: Registered protocol family 10 [ 16.376000] lo: Disabled Privacy Extensions [ 16.448000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 16.448000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 16.632000] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00 [ 16.632000] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c40 [ 16.744000] Linux agpgart interface v0.102 (c) Dave Jones [ 16.752000] parport_pc 00:0a: reported by Plug and Play ACPI [ 16.752000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] [ 16.752000] input: PC Speaker as /class/input/input4 [ 16.824000] nvidia: module license 'NVIDIA' taints kernel. [ 17.076000] ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16 [ 17.076000] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 21 [ 17.076000] PCI: Setting latency timer of device 0000:03:00.0 to 64 [ 17.076000] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.19 Wed Sep 12 14:12:24 PDT 2007 [ 17.276000] loop: module loaded [ 17.292000] lp0: using parport0 (interrupt-driven). [ 17.352000] Adding 10891256k swap on /dev/mapper/interserv-swap_1. Priority:-1 extents:1 across:10891256k [ 17.784000] EXT3 FS on dm-0, internal journal [ 18.120000] kjournald starting. Commit interval 5 seconds [ 18.120000] EXT3 FS on sda1, internal journal [ 18.120000] EXT3-fs: mounted filesystem with ordered data mode. [ 18.880000] No dock devices found. [ 18.888000] input: Power Button (FF) as /class/input/input5 [ 18.888000] ACPI: Power Button (FF) [PWRF] [ 18.888000] input: Power Button (CM) as /class/input/input6 [ 18.888000] ACPI: Power Button (CM) [PWRB] [ 19.116000] powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ processors (version 2.00.00) [ 19.116000] powernow-k8: MP systems not supported by PSB BIOS structure [ 19.116000] powernow-k8: MP systems not supported by PSB BIOS structure [ 20.424000] eth0: no link during initialization. [ 20.424000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 21.420000] Capability LSM initialized [ 21.796000] ppdev: user-space parallel port driver [ 27.372000] eth1: no IPv6 routers present [ 28.244000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) [ 28.244000] apm: disabled - APM is not SMP safe. [ 29.724000] Bluetooth: Core ver 2.11 [ 29.724000] NET: Registered protocol family 31 [ 29.724000] Bluetooth: HCI device and connection manager initialized [ 29.724000] Bluetooth: HCI socket layer initialized [ 29.736000] Bluetooth: L2CAP ver 2.8 [ 29.736000] Bluetooth: L2CAP socket layer initialized [ 29.804000] Bluetooth: RFCOMM socket layer initialized [ 29.804000] Bluetooth: RFCOMM TTY layer initialized [ 29.804000] Bluetooth: RFCOMM ver 1.8 [ 33.344000] NET: Registered protocol family 17 [ 91.856000] end_request: I/O error, dev fd0, sector 0 [ 108.916000] end_request: I/O error, dev fd0, sector 0 [ 1060.392000] sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) [ 1060.392000] sd 2:0:0:0: [sdc] Write Protect is off [ 1060.392000] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 1060.396000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1060.396000] sdc: [ 1062.400000] sd 2:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB) [ 1062.400000] sd 2:0:0:0: [sdc] Write Protect is off [ 1062.400000] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 1062.400000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1062.400000] sdc: [ 1256.092000] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 [ 1256.092000] ata2.00: cmd ef/ab:00:00:00:00/00:00:00:00:00/40 tag 0 cdb 0x0 data 0 [ 1256.092000] res 51/04:00:00:00:00/00:00:00:00:00/40 Emask 0x1 (device error) [ 1256.108000] ata2.00: configured for UDMA/133 [ 1256.108000] ata2: EH complete [ 1256.108000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1256.108000] sd 1:0:0:0: [sdb] Write Protect is off [ 1256.108000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1256.108000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1256.124000] ata2.00: configured for UDMA/133 [ 1256.124000] ata2: EH complete [ 1256.124000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1256.124000] sd 1:0:0:0: [sdb] Write Protect is off [ 1256.124000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1256.256000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1365.560000] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 [ 1365.560000] ata2.00: cmd ef/ab:00:00:00:00/00:00:00:00:00/40 tag 0 cdb 0x0 data 0 [ 1365.560000] res 51/04:00:00:00:00/00:00:00:00:00/40 Emask 0x1 (device error) [ 1365.584000] ata2.00: configured for UDMA/133 [ 1365.584000] ata2: EH complete [ 1365.584000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1365.584000] sd 1:0:0:0: [sdb] Write Protect is off [ 1365.584000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1365.584000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1365.600000] ata2.00: configured for UDMA/133 [ 1365.600000] ata2: EH complete [ 1365.600000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1365.600000] sd 1:0:0:0: [sdb] Write Protect is off [ 1365.600000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1365.712000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1391.264000] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 [ 1391.264000] ata2.00: cmd ef/ab:00:00:00:00/00:00:00:00:00/40 tag 0 cdb 0x0 data 0 [ 1391.264000] res 51/04:00:00:00:00/00:00:00:00:00/40 Emask 0x1 (device error) [ 1391.280000] ata2.00: configured for UDMA/133 [ 1391.280000] ata2: EH complete [ 1391.280000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1391.280000] sd 1:0:0:0: [sdb] Write Protect is off [ 1391.280000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1391.280000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1391.296000] ata2.00: configured for UDMA/133 [ 1391.296000] ata2: EH complete [ 1391.296000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1391.296000] sd 1:0:0:0: [sdb] Write Protect is off [ 1391.296000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1391.400000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1440.456000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1440.456000] sd 1:0:0:0: [sdb] Write Protect is off [ 1440.456000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1440.456000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1440.456000] sdb: sdb1 < > [ 1442.476000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1442.476000] sd 1:0:0:0: [sdb] Write Protect is off [ 1442.476000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1442.480000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1442.480000] sdb: sdb1 < > [ 1571.528000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1571.528000] sd 1:0:0:0: [sdb] Write Protect is off [ 1571.528000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1571.528000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1571.528000] sdb: sdb1 < sdb5 > [ 1573.528000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1573.528000] sd 1:0:0:0: [sdb] Write Protect is off [ 1573.528000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1573.528000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1573.528000] sdb: sdb1 < sdb5 > [ 1768.788000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1768.788000] sd 1:0:0:0: [sdb] Write Protect is off [ 1768.788000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1768.788000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1768.788000] sdb: [ 1770.824000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1770.824000] sd 1:0:0:0: [sdb] Write Protect is off [ 1770.824000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1770.824000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1770.824000] sdb: [ 1798.564000] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 [ 1798.564000] ata2.00: cmd ef/ab:00:00:00:00/00:00:00:00:00/40 tag 0 cdb 0x0 data 0 [ 1798.564000] res 51/04:00:00:00:00/00:00:00:00:00/40 Emask 0x1 (device error) [ 1798.588000] ata2.00: configured for UDMA/133 [ 1798.588000] ata2: EH complete [ 1798.588000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1798.588000] sd 1:0:0:0: [sdb] Write Protect is off [ 1798.588000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1798.588000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1798.604000] ata2.00: configured for UDMA/133 [ 1798.604000] ata2: EH complete [ 1798.604000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1798.604000] sd 1:0:0:0: [sdb] Write Protect is off [ 1798.604000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1798.700000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1871.892000] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 [ 1871.892000] ata2.00: cmd ef/ab:00:00:00:00/00:00:00:00:00/40 tag 0 cdb 0x0 data 0 [ 1871.892000] res 51/04:00:00:00:00/00:00:00:00:00/40 Emask 0x1 (device error) [ 1871.908000] ata2.00: configured for UDMA/133 [ 1871.908000] ata2: EH complete [ 1871.908000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1871.908000] sd 1:0:0:0: [sdb] Write Protect is off [ 1871.908000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1871.908000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1871.924000] ata2.00: configured for UDMA/133 [ 1871.924000] ata2: EH complete [ 1871.924000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1871.924000] sd 1:0:0:0: [sdb] Write Protect is off [ 1871.924000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1872.024000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1935.644000] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 [ 1935.644000] ata2.00: cmd ef/ab:00:00:00:00/00:00:00:00:00/40 tag 0 cdb 0x0 data 0 [ 1935.644000] res 51/04:00:00:00:00/00:00:00:00:00/40 Emask 0x1 (device error) [ 1935.660000] ata2.00: configured for UDMA/133 [ 1935.660000] ata2: EH complete [ 1935.660000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1935.660000] sd 1:0:0:0: [sdb] Write Protect is off [ 1935.660000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1935.660000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1935.676000] ata2.00: configured for UDMA/133 [ 1935.676000] ata2: EH complete [ 1935.676000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1935.676000] sd 1:0:0:0: [sdb] Write Protect is off [ 1935.676000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1935.776000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1978.308000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1978.308000] sd 1:0:0:0: [sdb] Write Protect is off [ 1978.308000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1978.308000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1978.308000] sdb: sdb1 [ 1980.312000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 1980.312000] sd 1:0:0:0: [sdb] Write Protect is off [ 1980.312000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 1980.312000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1980.312000] sdb: sdb1 [ 2014.788000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 2014.788000] sd 1:0:0:0: [sdb] Write Protect is off [ 2014.788000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2014.788000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 2014.788000] sdb: [ 2016.792000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 2016.792000] sd 1:0:0:0: [sdb] Write Protect is off [ 2016.792000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2016.792000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 2016.792000] sdb: [ 2429.696000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 2429.696000] sd 1:0:0:0: [sdb] Write Protect is off [ 2429.696000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2429.696000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 2429.696000] sdb: sdb1 [ 2431.708000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB) [ 2431.712000] sd 1:0:0:0: [sdb] Write Protect is off [ 2431.712000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2431.712000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 2431.712000] sdb: sdb1 itgen-admin@interserv:~$ lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:06.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:0b.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) 02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 03) 02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 03) 03:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 SE] (rev a1) itgen-admin@interserv:~$ lsmod Module Size Used by af_packet 24840 2 rfcomm 42136 2 l2cap 26240 11 rfcomm bluetooth 57060 4 rfcomm,l2cap ppdev 10244 0 capability 5896 0 cpufreq_powersave 2688 0 cpufreq_ondemand 9612 0 cpufreq_userspace 5280 0 cpufreq_stats 7232 0 freq_table 5792 2 cpufreq_ondemand,cpufreq_stats cpufreq_conservative 8072 0 sbs 19592 0 container 5504 0 video 18060 0 button 8976 0 dock 10656 0 ac 6148 0 battery 11012 0 sbp2 24072 0 lp 12580 0 loop 19076 0 nvidia 6221648 24 pcspkr 4224 0 agpgart 35016 1 nvidia parport_pc 37412 1 parport 37448 3 ppdev,lp,parport_pc psmouse 39952 0 serio_raw 8068 0 i2c_nforce2 7040 0 shpchp 34580 0 pci_hotplug 32704 1 shpchp k8temp 6656 0 i2c_core 26112 2 nvidia,i2c_nforce2 ipv6 273892 22 joydev 11328 0 evdev 11136 4 ext3 133896 2 jbd 60456 1 ext3 mbcache 9732 1 ext3 sg 36764 0 sr_mod 17828 0 cdrom 37536 1 sr_mod sd_mod 30336 5 usbhid 29536 0 hid 28928 1 usbhid floppy 60004 0 pata_jmicron 7552 0 ahci 23300 0 amd74xx 15260 0 [permanent] ide_core 116804 1 amd74xx ehci_hcd 36492 0 ohci_hcd 22916 0 usbcore 138632 4 usbhid,ehci_hcd,ohci_hcd ohci1394 36528 0 ieee1394 96312 2 sbp2,ohci1394 forcedeth 51592 0 sata_nv 20612 4 ata_generic 8452 0 libata 125168 4 pata_jmicron,ahci,sata_nv,ata_generic scsi_mod 147084 5 sbp2,sg,sr_mod,sd_mod,libata raid10 26496 0 raid456 128016 0 xor 16904 1 raid456 raid1 25984 0 raid0 9728 0 multipath 9984 0 linear 7552 0 md_mod 82324 6 raid10,raid456,raid1,raid0,multipath,linear dm_mirror 24448 0 dm_snapshot 18980 0 dm_mod 58816 9 dm_mirror,dm_snapshot thermal 14344 0 processor 32072 1 thermal fan 5764 0 commoncap 8320 1 capability fuse 47124 1 itgen-admin@interserv:~$