# dmesg
oger@thecheat) (gcc version 4.1.2) #5 Fri Feb 29 23:06:48 EST 2008
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: TCT_HAMMER
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 8192
  DMA zone: 64 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 8128 pages, LIFO batch:0
  Normal zone: 0 pages used for memmap
CPU S3C2410A (id 0x32410002)
S3C2410: core 202.800 MHz, memory 101.400 MHz, peripheral 50.700 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttySAC0 root=/dev/ram0 
irq: clearing subpending status 00000002
PID hash table entries: 128 (order: 7, 512 bytes)
timer tcon=00000000, tcnt a509, tcfg 00000200,00000000, usec 00001e4c
Console: colour dummy device 80x30
selected clock c01e6f90 (pclk) quot 27, calc 113169
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 32MB = 32MB total
Memory: 29400KB available (1760K code, 166K data, 92K init)
Calibrating delay loop... 101.17 BogoMIPS (lpj=252928)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410: Initialising architecture
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 1024K
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) �� 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
s3c2410-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
drivers/net/usb/kaweth.c: Driver loading
usbcore: registered new interface driver kaweth
physmap platform flash device: 01000000 at 00000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x20000,blocks=128
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 2 MTD partitions on "physmap-flash.0":
0x00000000-0x00240000 : "System"
0x00240000-0x01000000 : "JFFS2"
usbmon: debugfs is not available
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
s3c2410-ohci s3c2410-ohci: s3c2410_start_hc:
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
s3c2410-ohci s3c2410-ohci: created debug files
s3c2410-ohci s3c2410-ohci: OHCI controller state
s3c2410-ohci s3c2410-ohci: OHCI 1.0, NO legacy support registers
s3c2410-ohci s3c2410-ohci: control 0x083 HCFS=operational CBSR=3
s3c2410-ohci s3c2410-ohci: cmdstatus 0x00000 SOC=0
s3c2410-ohci s3c2410-ohci: intrstatus 0x00000004 SF
s3c2410-ohci s3c2410-ohci: intrenable 0x8000005a MIE RHSC UE RD WDH
s3c2410-ohci s3c2410-ohci: hcca frame #0005
s3c2410-ohci s3c2410-ohci: roothub.a 02001202 POTPGT=2 NOCP NPS NDP=2(2)
s3c2410-ohci s3c2410-ohci: roothub.b 00000000 PPCM=0000 DR=0000
s3c2410-ohci s3c2410-ohci: roothub.status 00008000 DRWE
s3c2410-ohci s3c2410-ohci: roothub.portstatus [0] 0x00010101 CSC PPS CCS
s3c2410-ohci s3c2410-ohci: roothub.portstatus [1] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 2.6.22 ohci_hcd
usb usb1: SerialNumber: s3c24xx
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa006,0x2900,0x0000,c0253a88,000f)
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: power on to power good time: 4ms
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa000,0x0000,0x0000,c0253a44,0004)
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2303,0x0008,0x0001,c0253a44,0000)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2303,0x0008,0x0002,c0253a44,0000)
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
Initializing USB Mass Storage driver...
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0010,0x0001,c026be54,0000)
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2303,0x0004,0x0001,c026bdc4,0000)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026bda4,0004)
s3c2410-ohci s3c2410-ohci: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0014,0x0001,c026bdc4,0000)
usb 1-1: new full speed USB device using s3c2410-ohci and address 2
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2303,0x0004,0x0001,c026bdc4,0000)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026bda4,0004)
s3c2410-ohci s3c2410-ohci: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0014,0x0001,c026bdc4,0000)
usb 1-1: ep0 maxpacket = 8
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=2, Product=3, SerialNumber=1
usb 1-1: Product: 3COM USB Network Interface (3C19250)
usb 1-1: Manufacturer: 3COM
usb 1-1: SerialNumber: 0050DA333B80
usb 1-1: uevent
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
usb 1-1:1.0: uevent
kaweth 1-1:1.0: usb_probe_interface
kaweth 1-1:1.0: usb_probe_interface - got id
drivers/net/usb/kaweth.c: Kawasaki Device Probe (Device number:2): 0x0506:0x03e8:0x0003
drivers/net/usb/kaweth.c: Device at c08977f0
drivers/net/usb/kaweth.c: Descriptor length: 12 type: 1
drivers/net/usb/kaweth.c: Resetting.
drivers/net/usb/kaweth.c: kaweth_reset(c088b180)
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: kaweth_reset() returns 0.
drivers/net/usb/kaweth.c: Downloading firmware...
drivers/net/usb/kaweth.c: High: 12, Low:197
drivers/net/usb/kaweth.c: Downloading firmware at c01e7cbc to kaweth device at c088b180
drivers/net/usb/kaweth.c: Firmware length: 3276
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: High: 2, Low:103
drivers/net/usb/kaweth.c: Downloading firmware at c01e8988 to kaweth device at c088b180
drivers/net/usb/kaweth.c: Firmware length: 622
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: High: 0, Low:175
drivers/net/usb/kaweth.c: Downloading firmware at c01e8bf6 to kaweth device at c088b180
drivers/net/usb/kaweth.c: Firmware length: 182
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: High: 0, Low:15
drivers/net/usb/kaweth.c: Downloading firmware at c01e8cac to kaweth device at c088b180
drivers/net/usb/kaweth.c: Firmware length: 22
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: Triggering firmware
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: Firmware loaded.  I'll be back...
kaweth: probe of 1-1:1.0 failed with error -5
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0002,c026be34,0004)
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
s3c2410_udc: debugfs dir creation failed -19
gs_bind: Gadget Serial v2.2 bound
gs_module_init: Gadget Serial v2.2 loaded
input: gpio-keys as /class/input/input0
evbug.c: Connected device: "gpio-keys", gpio-keys/input0
input: TCT Hammer beeper as /class/input/input1
evbug.c: Connected device: "TCT Hammer beeper", hammer/gpio
Registered led device: led0
Registered led device: led1
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
length error
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 92K
selected clock c01e6f90 (pclk) quot 27, calc 113169
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0010,0x0001,c026be54,0000)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0011,0x0001,c026be54,0000)
hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usb 1-1: USB disconnect, address 2
usb 1-1: unregistering device
usb 1-1: usb_disable_device nuking all URBs
usb 1-1: unregistering interface 1-1:1.0
usb_endpoint usbdev1.2_ep81: ep_device_release called for usbdev1.2_ep81
usb_endpoint usbdev1.2_ep02: ep_device_release called for usbdev1.2_ep02
usb_endpoint usbdev1.2_ep83: ep_device_release called for usbdev1.2_ep83
usb 1-1:1.0: uevent
usb 1-1:1.0: uevent
usb_endpoint usbdev1.2_ep00: ep_device_release called for usbdev1.2_ep00
usb 1-1: uevent
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
selected clock c01e6f90 (pclk) quot 27, calc 113169
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
selected clock c01e6f90 (pclk) quot 27, calc 113169
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0002
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0010,0x0001,c026be54,0000)
hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026be34,0004)
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2303,0x0004,0x0001,c026bdc4,0000)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026bda4,0004)
s3c2410-ohci s3c2410-ohci: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0014,0x0001,c026bdc4,0000)
usb 1-1: new full speed USB device using s3c2410-ohci and address 3
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2303,0x0004,0x0001,c026bdc4,0000)
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0xa300,0x0000,0x0001,c026bda4,0004)
s3c2410-ohci s3c2410-ohci: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
s3c2410-ohci s3c2410-ohci: s3c2410_hub_control(c0890008,0x2301,0x0014,0x0001,c026bdc4,0000)
usb 1-1: ep0 maxpacket = 8
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=2, Product=3, SerialNumber=1
usb 1-1: Product: 3COM USB Network Interface (3C19250)
usb 1-1: Manufacturer: 3COM
usb 1-1: SerialNumber: 0050DA333B80
usb 1-1: uevent
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
usb 1-1:1.0: uevent
kaweth 1-1:1.0: usb_probe_interface
kaweth 1-1:1.0: usb_probe_interface - got id
drivers/net/usb/kaweth.c: Kawasaki Device Probe (Device number:3): 0x0506:0x03e8:0x0203
drivers/net/usb/kaweth.c: Device at c1cf3680
drivers/net/usb/kaweth.c: Descriptor length: 12 type: 1
drivers/net/usb/kaweth.c: Resetting.
drivers/net/usb/kaweth.c: kaweth_reset(c09363a0)
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: kaweth_reset() returns 0.
drivers/net/usb/kaweth.c: Firmware present in device.
drivers/net/usb/kaweth.c: Reading kaweth configuration
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: Statistics collection: 13fbffff
drivers/net/usb/kaweth.c: Multicast filter limit: 80
drivers/net/usb/kaweth.c: MTU: 1514
drivers/net/usb/kaweth.c: Read MAC address 00:50:da:33:3b:80
drivers/net/usb/kaweth.c: Setting URB size to 1664
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: Set SOFS wait to 5
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: Set receive filter to 28
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: Initializing net device.
drivers/net/usb/kaweth.c: kaweth interface created at eth0
drivers/net/usb/kaweth.c: Kaweth probe returning.
selected clock c01e6f90 (pclk) quot 27, calc 113169
selected clock c01e6f90 (pclk) quot 27, calc 113169
selected clock c01e6f90 (pclk) quot 27, calc 113169
drivers/net/usb/kaweth.c: Opening network device.
drivers/net/usb/kaweth.c: Setting Rx mode to 28
drivers/net/usb/kaweth.c: Setting Rx mode to 28
drivers/net/usb/kaweth.c: Setting Rx mode to 28
drivers/net/usb/kaweth.c: kaweth_control()
drivers/net/usb/kaweth.c: in_interrupt()
drivers/net/usb/kaweth.c: Failed to set Rx mode: -16
#