Linux version 2.6.24.2 (siemer@panorama) (gcc version 4.1.2) #1 Fri Apr 11 00:40:24 CEST 2008 console [early0] enabled CPU revision is: 00018448 (MIPS 4KEc) Clocks: prediv: 1, postdiv: 1, mul: 10 TI AR7 (TNETD7300), ID: 0x0005, Revision: 0x21 Determined physical RAM map: memory: 01000000 @ 14000000 (usable) Entering add_active_range(0, 81920, 86016) 0 entries of 256 used Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 81920 -> 86016 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 81920 -> 86016 On node 0 totalpages: 4096 Normal zone: 32 pages used for memmap Normal zone: 0 pages reserved Normal zone: 4064 pages, LIFO batch:0 Movable zone: 0 pages used for memmap Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064 Kernel command line: init=/etc/preinit rootfstype=squashfs,jffs2, console=ttyS0,38400n8 Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes Synthesized clear page handler (26 instructions). Synthesized copy page handler (46 instructions). Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 64 (order: 6, 256 bytes) Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) Memory: 12512k/16384k available (2033k kernel code, 3872k reserved, 428k data, 128k init, 0k highmem) SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Calibrating delay loop... 149.91 BogoMIPS (lpj=749568) Mount-cache hash table entries: 512 net_namespace: 64 bytes NET: Registered protocol family 16 Time: MIPS clocksource has been installed. Switched to high resolution mode on CPU 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 512 (order: 0, 4096 bytes) TCP bind hash table entries: 512 (order: -1, 2048 bytes) TCP: Hash tables configured (established 512 bind 512) TCP reno registered squashfs: version 3.0 (2006/03/15) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a TI-AR7 console handover: boot [early0] -> real [ttyS0] serial8250: ttyS1 at MMIO 0x8610f00 (irq = 16) is a TI-AR7 Fixed MDIO Bus: probed cpmac-mii: probed cpmac cpmac.1: no PHY present cpmac: device eth0 (regs: 08610000, irq: 27, phy: , mac: 00:13:10:f2:37:a2) physmap platform flash device: 00800000 at 10000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0 Amd/Fujitsu Extended Query Table at 0x0040 physmap-flash.0: Swapping erase regions for broken CFI table. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available 4 ar7part partitions found on MTD device physmap-flash.0 Creating 4 MTD partitions on "physmap-flash.0": 0x00000000-0x00010000 : "loader" 0x00010000-0x00020000 : "config" 0x00020000-0x00400000 : "linux" 0x000e61d6-0x00400000 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=320000, len=E0000 0x00320000-0x00400000 : "rootfs_data" ar7_wdt: disabling watchdog timer ar7_wdt: timer margin 59 seconds (prescale 65535, change 57180, freq 62500000) Registered led device: status vlynq0: regs 0x08611800, irq 29, mem 0x04000000 vlynq1: regs 0x08611c00, irq 33, mem 0x0c000000 nf_conntrack version 0.5.0 (1024 buckets, 4096 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP vegas registered NET: Registered protocol family 1 NET: Registered protocol family 17 Bridge firewalling registered 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 128k freed Please be patient, while OpenWrt loads ... Algorithmics/MIPS FPU Emulator v1.5 mini_fo: using base directory: / mini_fo: using storage directory: /jffs PHY: 0:1f - Link is Down NET: Registered protocol family 8 NET: Registered protocol family 20 PPP generic driver version 2.4.2 arp_tables: (C) 2002 David S. Miller acx: this driver is still EXPERIMENTAL acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them acx: running on a little-endian CPU acx: PCI/VLYNQ module v0.3.37 initialized, waiting for cards to probe... vlynq0: using local clock divisor 2 vlynq0: using local clock divisor 2 acx: found TI TNETW1130-based wireless network card at vlynq0, irq:80, phymem:0x4000000, mem:0xa4000000 initial debug setting is 0x000A using IRQ 80 acx: need to load firmware for acx111 chipset with radio ID 16, please provide via firmware hotplug: acx: either one file only (ombined firmware image file, radio-specific) or two files (radio-less base image file *plus* separate adio-specific extension file) requesting firmware image 'tiacx111c16' acx_write_fw (main/combined): 0 acx_validate_fw (main/combined): 0 initializing max packet templates dump queue head (from card): len: 24 tx_memory_block_address: 19E40 rx_memory_block_address: 15240 tx1_queue address: 14774 rx1_queue address: 14434 NVS_vendor_offs:0221 probe_delay:200 eof_memory:1114112 CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01 AntennaID:00 Len:02 Data:01 02 PowerLevelID:01 Len:02 Data:001E 000A DataRatesID:02 Len:05 Data:02 04 11 22 44 DomainID:03 Len:06 Data:41 20 30 31 32 40 ProductID:04 Len:09 Data:TI ACX100 ManufacturerID:05 Len:07 Data:TI Test get_mask 0x00004182, set_mask 0x00000000 don't know how to get sensitivity for radio type 0x16 got sensitivity value 0 got antenna value 0x4A got regulatory domain 0x41 get_mask 0x00000000, set_mask 0x00000000 - after update new ratevector: 82 84 0B 0C 12 16 18 24 2C 30 48 60 6C setting RXconfig to 2010:0FDD acx: === chipset TNETW1130, radio type 0x16 (Radia), form factor 0x01 ((mini-)PCI / CardBus), EEPROM version 0x05: uploaded firmware 'Rev 2.3.1.31' === creating /proc entry driver/acx_wlan%d creating /proc entry driver/acx_wlan%d_diag creating /proc entry driver/acx_wlan%d_eeprom creating /proc entry driver/acx_wlan%d_phy acx v0.3.37: net device wlan%d, driver compiled against wireless extensions 22 and Linux 2.6.24.2 using IRQ 80 registered device TI Avalanche SAR Sangam detected requesting firmware image "ar0700xx.bin" avsar firmware released Creating new root folder avalanche in the proc for the driver stats Texas Instruments ATM driver: version:[7.03.01.00] NET: Registered protocol family 24 ar7_wdt: enabling watchdog timer