CM> Adjusting the initial ranging power to 33.0 dBmV... Logging event: No Ranging Response received - T3 time-out Sending syslog message from IF 1 to 192.168.100.10: <130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o ut 0x0001f1e4 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK ET_ERROR: 65 docsDevEvSyslog::Send - sendto failure -1 CM> 0x0001f432 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig noring... CM> 0x0001f7b6 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig noring... RNG-RSP Stat=Continue or ds freq=573000000 or us id=9 0x0001f7f2 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf f... Deleting DOCSIS 1.0 CoS Settings for SID 0x0 0x0001f8ba ['CmDocsisCtlThread' id=0x807bda80] BcmDocsisCmHalIf::DeleteAllServic eFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service Flows, along with associated Classifiers and PHS rules... Stopping DHCP/ToD/TFTP (client requested)... BcmSnmpAgent::RestartPendingEvent for SB5100 CM Agent SB5100 CM Agent setting V1/V2 view to SB5100 CM Agent sending deferred traps... Done w/ deferred traps. SB5100 CM Agent ConfigIp: Ip=0.0.0.0, Subnet=0.0.0.0, Gateway=0.0.0.0 Ip addr is the same, not rebinding. v1Trap: linkDownTrap(if2) 192.168.100.1->192.168.100.10:226, cmty="public" CmSnmpAgent::ResetMibDefaults not restting due to factory mode SB5100 CPE Agent setting V1/V2 view to docsisNmAccessView Non-Vol Settings successfully written to the device. 0x0001f8c4 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ResetRngSta te: (CmDocsisCtlThread) 0x0001f8c4 ['CmPropaneCtlThread' id=0x807b9800] BcmCmPropaneCtlThread::ServiceMe ssageQueue: (CmPropaneCtlThread) WARNING - Didn't handle command IpAddressLost in the current state (2, PropaneCmInitial)! SB5100 CM Event Log sending deferred async messages... Done w/ deferred msgs Received a UCD for Upstream Channel 5! CM> Received a UCD for Upstream Channel 6! Received a UCD for Upstream Channel 1! 0x0001fb3a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... Received a UCD for Upstream Channel 2! CM> Received a UCD for Upstream Channel 3! Received a UCD for Upstream Channel 4! 0x0001febe ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... Received a UCD for Upstream Channel 5! A target Us Chan Id was specified (9), but doesn't exist OR can't be used! Sele cting the first available Us Channel Id... Selecting UCD for Us Channel 5 BcmCmUsPhyOverheadSettings::ComputeReqDataPhyToMacTable() burst descriptor not f ound for kReqDataIUC. Upstream Frequency = 25000000 Found QAM16 = true 0x0001ff2c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun chDsTimeSync: (CmDocsisCtlThread) entering... new_us_scdma_enabled = false fLastDsClockModeIsScdma = false fCmDsTargetingState = kDsOkUsPending IsDccContext() = false 0x0001ff2c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun chDsTimeSync: (CmDocsisCtlThread) ds time sync should be ok. resume us init no w. 0x0001ff2c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::DsSyncOkRes umeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging. Beginning initial ranging... Using default initial upstream power = 8.0 dBmV Logging event: T501.0 Acquired Downstream (567000000 Hz)........ SUCCESS Sending syslog message from IF 1 to 192.168.100.10: <134> CABLEMODEM [Motorola Corporation]: <2223898630> T501.0 Acquired Downstre am (567000000 Hz)........ SUCCESS 0x0001ff40 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK ET_ERROR: 65 docsDevEvSyslog::Send - sendto failure -1 v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:226, cmty="public" CM> 0x00020242 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig noring... Adjusting the initial ranging power to 33.0 dBmV... Logging event: No Ranging Response received - T3 time-out Sending syslog message from IF 1 to 192.168.100.10: <130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o ut 0x0002024c ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK ET_ERROR: 65 docsDevEvSyslog::Send - sendto failure -1 CM> 0x000205c6 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig noring... RNG-RSP Stat=Continue or ds freq=573000000 or us id=11 0x0002085a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf f... Deleting DOCSIS 1.0 CoS Settings for SID 0x0 0x00020922 ['CmDocsisCtlThread' id=0x807bda80] BcmDocsisCmHalIf::DeleteAllServic eFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service Flows, along with associated Classifiers and PHS rules... Stopping DHCP/ToD/TFTP (client requested)... BcmSnmpAgent::RestartPendingEvent for SB5100 CM Agent SB5100 CM Agent setting V1/V2 view to SB5100 CM Agent sending deferred traps... Done w/ deferred traps. SB5100 CM Agent ConfigIp: Ip=0.0.0.0, Subnet=0.0.0.0, Gateway=0.0.0.0 Ip addr is the same, not rebinding. v1Trap: linkDownTrap(if2) 192.168.100.1->192.168.100.10:226, cmty="public" CmSnmpAgent::ResetMibDefaults not restting due to factory mode SB5100 CPE Agent setting V1/V2 view to docsisNmAccessView Non-Vol Settings successfully written to the device. 0x0002092c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ResetRngSta te: (CmDocsisCtlThread) 0x0002092c ['CmPropaneCtlThread' id=0x807b9800] BcmCmPropaneCtlThread::ServiceMe ssageQueue: (CmPropaneCtlThread) WARNING - Didn't handle command IpAddressLost in the current state (2, PropaneCmInitial)! SB5100 CM Event Log sending deferred async messages... Done w/ deferred msgs NonVolDeviceDriver::NonVolDriverWrite: WARNING - Dynamic NonVol is 'full' - no more free segments; need to erase and start over! NonVolDeviceDriver::NonVolDriverWrite: WARNING - Erasing flash region; a power failure here will cause settings to be lost! 0x0002094a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... Received a UCD for Upstream Channel 3! Received a UCD for Upstream Channel 4! Received a UCD for Upstream Channel 5! CM> Received a UCD for Upstream Channel 6! 0x00020cce ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... Received a UCD for Upstream Channel 1! CM> Received a UCD for Upstream Channel 2! Received a UCD for Upstream Channel 3! A target Us Chan Id was specified (11), but doesn't exist OR can't be used! Sel ecting the first available Us Channel Id... Selecting UCD for Us Channel 3 BcmCmUsPhyOverheadSettings::ComputeReqDataPhyToMacTable() burst descriptor not f ound for kReqDataIUC. Upstream Frequency = 21000000 Found QAM16 = true 0x00020fd0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun chDsTimeSync: (CmDocsisCtlThread) entering... new_us_scdma_enabled = false fLastDsClockModeIsScdma = false fCmDsTargetingState = kDsOkUsPending IsDccContext() = false 0x00020fd0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun chDsTimeSync: (CmDocsisCtlThread) ds time sync should be ok. resume us init no w. 0x00020fd0 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::DsSyncOkRes umeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging. Beginning initial ranging... Using default initial upstream power = 8.0 dBmV Logging event: T501.0 Acquired Downstream (567000000 Hz)........ SUCCESS Sending syslog message from IF 1 to 192.168.100.10: <134> CABLEMODEM [Motorola Corporation]: <2223898630> T501.0 Acquired Downstre am (567000000 Hz)........ SUCCESS 0x00020fe4 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK ET_ERROR: 65 docsDevEvSyslog::Send - sendto failure -1 v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:226, cmty="public" 0x00021052 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... CM> Adjusting the initial ranging power to 33.0 dBmV... Logging event: No Ranging Response received - T3 time-out Sending syslog message from IF 1 to 192.168.100.10: <130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o ut 0x000211ec ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK ET_ERROR: 65 docsDevEvSyslog::Send - sendto failure -1 RNG-RSP Stat=Continue or ds freq=573000000 or us id=9 0x0002134a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf f... Deleting DOCSIS 1.0 CoS Settings for SID 0x0 0x00021412 ['CmDocsisCtlThread' id=0x807bda80] BcmDocsisCmHalIf::DeleteAllServic eFlows: (DOCSIS CableModem HalIf) Deleting all Upstream and Downstream Service Flows, along with associated Classifiers and PHS rules... Stopping DHCP/ToD/TFTP (client requested)... BcmSnmpAgent::RestartPendingEvent for SB5100 CM Agent SB5100 CM Agent setting V1/V2 view to SB5100 CM Agent sending deferred traps... Done w/ deferred traps. SB5100 CM Agent ConfigIp: Ip=0.0.0.0, Subnet=0.0.0.0, Gateway=0.0.0.0 Ip addr is the same, not rebinding. v1Trap: linkDownTrap(if2) 192.168.100.1->192.168.100.10:226, cmty="public" CmSnmpAgent::ResetMibDefaults not restting due to factory mode SB5100 CPE Agent setting V1/V2 view to docsisNmAccessView Non-Vol Settings successfully written to the device. 0x0002141c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::ResetRngSta te: (CmDocsisCtlThread) 0x0002141c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... 0x0002141c ['CmPropaneCtlThread' id=0x807b9800] BcmCmPropaneCtlThread::ServiceMe ssageQueue: (CmPropaneCtlThread) WARNING - Didn't handle command IpAddressLost in the current state (2, PropaneCmInitial)! SB5100 CM Event Log sending deferred async messages... Done w/ deferred msgs Received a UCD for Upstream Channel 2! CM> Received a UCD for Upstream Channel 3! Received a UCD for Upstream Channel 4! 0x0002175a ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... Received a UCD for Upstream Channel 5! CM> Received a UCD for Upstream Channel 6! Received a UCD for Upstream Channel 1! 0x00021ade ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxMacMg tMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ignori ng... Received a UCD for Upstream Channel 2! A target Us Chan Id was specified (9), but doesn't exist OR can't be used! Sele cting the first available Us Channel Id... Selecting UCD for Us Channel 2 BcmCmUsPhyOverheadSettings::ComputeReqDataPhyToMacTable() burst descriptor not f ound for kReqDataIUC. Upstream Frequency = 21000000 Found QAM16 = true 0x00021b4c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun chDsTimeSync: (CmDocsisCtlThread) entering... new_us_scdma_enabled = false fLastDsClockModeIsScdma = false fCmDsTargetingState = kDsOkUsPending IsDccContext() = false 0x00021b4c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::TestAndLaun chDsTimeSync: (CmDocsisCtlThread) ds time sync should be ok. resume us init no w. 0x00021b4c ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::DsSyncOkRes umeUsInit: (CmDocsisCtlThread) pre-REG upstream target case...starting initial ranging. Beginning initial ranging... Using default initial upstream power = 8.0 dBmV Logging event: T501.0 Acquired Downstream (567000000 Hz)........ SUCCESS Sending syslog message from IF 1 to 192.168.100.10: <134> CABLEMODEM [Motorola Corporation]: <2223898630> T501.0 Acquired Downstre am (567000000 Hz)........ SUCCESS 0x00021b60 ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK ET_ERROR: 65 docsDevEvSyslog::Send - sendto failure -1 v1Trap: cmTrapLog 192.168.100.1->192.168.100.10:226, cmty="public" CM> Adjusting the initial ranging power to 33.0 dBmV... Logging event: No Ranging Response received - T3 time-out Sending syslog message from IF 1 to 192.168.100.10: <130> CABLEMODEM [DOCSIS]: <82000200> No Ranging Response received - T3 time-o ut 0x00021cdc ['Event Log Thread' id=0x807b4820] BcmVxSocket::Sendto: ERROR - SOCK ET_ERROR: 65 docsDevEvSyslog::Send - sendto failure -1 CM> 0x00021e62 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig noring... CM> 0x000221e6 ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::SyncRxM acMgtMsg: (CmDocsisCtlThread) WARNING - Unknown message type received (32)! Ig noring... RNG-RSP Stat=Continue or ds freq=573000000 or us id=9 0x000222ea ['CmDocsisCtlThread' id=0x807bda80] BcmCmDocsisCtlThread::RngRspMsgEv ent: (CmDocsisCtlThread) WARNING - Calling PreRegUsChanChange! Appendix H stuf f... Connection to host lost. C:\Documents and Settings\home>